electronics, repairs, service manuals and datasheets discussion community for the repairs professionals and technicians
FAQSearchMembersGroupsRegisterProfilePM'sLogin/Out
*** SONY BLINK CODES ***
Goto page Previous  1, 2
 
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs
View previous topic :: View next topic  
Author Message
jts1957



Joined: 24 Nov 2008
Posts: 2476
Location: Far, Far Away

PostPosted: Sat Feb 07, 2009 10:58 pm    Post subject: Reply with quote

Sony Blink Codes Revised:
http://www.techlore.com/article/15444/?src=103
Back to top
View user's profile Send private message
Malik
Guest





PostPosted: Sun Feb 08, 2009 12:25 pm    Post subject: FX432M91 Reply with quote

AS PER NEW CODES, I HAVE REPLACED IC 8005.IT DID NOT WORK.
Back to top
arinc429
Guest





PostPosted: Mon Feb 23, 2009 5:26 pm    Post subject: 10 blinks Reply with quote

Sony asked 300 dollars to fix 10 blinking problem of TV kp-fx432M91.I decided to fix it myself on throw away basis, could not get much help for 10 blinks from Net. Bought Service Manual from net then few parts and finally above mentioned IC 8002 fixed the problem. Pls look for IC Part No. MCZ3001DB in D board, You will find two IC of same part number but look for the IC driving Two FETs of High Voltage Power supply section.
Q8013, Q8014, R8051 and IC 8002 are the essential components for HV section and these must be checked/replaced.
These all components cost only 12 Dollars in Middle East and 30 Dollars in USA and Sony may ask u minimum 250 dollars to fix 10 blinking problem.
Back to top
crina
Guest





PostPosted: Tue Oct 27, 2009 12:52 pm    Post subject: Reply with quote

I have Sony tv kv-29cs60k and the standby led blinks 14 times and does not switch on, anybody knows what is this?[/u][/b]
Back to top
[email protected]
Guest





PostPosted: Fri Dec 04, 2009 9:28 pm    Post subject: Re: 10 blinks Reply with quote

change ic smz in power supply
Back to top
lervinfix
Guest





PostPosted: Sat Dec 05, 2009 3:39 am    Post subject: Reply with quote

sir/maam... sony has 10 blinks no video...just because the sysytem cannot detect the video signal came from video chroma or jungle ic.. thers a 3 ways to fix that..
1st......resolder the jungle ic.(if has a jungle ic..some tv has no jungle ic only in the sysytem controll)....resolder the crt board..if no luck try number option..

2nd....adjust the screen adjustment found in the flyback..(just a little bit)if no luck back the screen adjustment in previouse position then refer to option 3..

3rd......reset the memory ic found near of system controll ic..has 8 pins ..if you dont have a ic programmer gadget to reset the memory .. try pick up a memory to another junk tv.. only to test it if any development..(make sure you dont pick a wrong one..only memory ic with 8 pins near or beside of system controll ic..)some memory has a lable named ATMEL Smile

hoped i can help..Smile
Back to top
Guest






PostPosted: Fri Jan 29, 2010 11:47 am    Post subject: Reply with quote

10 blinks means you have a problem in HV PROTECTION CIRCUIT, check and replace T8001,ic8002,q8013,8014,r8051 on D board or its line
Smile
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs All times are GMT
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


eServiceInfo on FB - Service Manuals Free Download - Service Diagrams

Free TV Schematics Download - HARDW.net - Pinout Master - Jabse Service Manual Search - Jabse.InK  - onTap.bg

SnimkiOt.com - Poblizo.com : пътешествия