Author |
Message |
matt123 |
Posted: Sun Sep 20, 2009 12:18 am Post subject: |
|
after following your instructions the screen is now working!
Thanks so much you've just saved me a minimum of $50 I was quoted at numerous repair shops. |
|
|
jts1957 |
Posted: Mon Sep 14, 2009 12:46 pm Post subject: |
|
If you were able to obtain the exact replacement from Yamaha, it would just plug in. Probable ain't gonna happen.
Cut all 4 wire to SAME length, splice ends, solder and insulate - you now have one "blob" at one point along wires.
If you stagger splices the "blob" is eliminated (or you have 4 smaller blobs, if you want to look at it another way).
Splicing: http://www.mmxpress.com/technical/connections.htm |
|
|
matt123 |
Posted: Mon Sep 14, 2009 6:37 am Post subject: |
|
Here is a picture of the old bulbs on the wire
http://i631.photobucket.com/albums/uu40/matthewk0123/IMG_3982.jpg
I'm guessing what you mean by staggering lengths is cutting the old bulbs off from each connecting wire at different points and then joining the new bulbs on by twisting the wires together?
Sorry but I don't know much about electronics
Thanks again |
|
|
jts1957 |
Posted: Sat Sep 12, 2009 11:58 am Post subject: |
|
6, 8, 12 and 14 are the "common" voltages. 35mA and 70mA are the "common" currents. And then they have different bulb diameters. You CAN put a smaller diameter bulb in a larger hole or you can usually enlarge a smaller hole to fit a larger bulb (within a certain range).
Select closest voltage. When you measure 10 volts, it usually is better to go to next higher (but may be dimmer). I like to keep a supply of ALL common miniature bulbs (8 types total) then I can try, and see the difference.
When wiring new ones in, cut old and new bulb wires at staggering lengths so splices (w/shrink tubing to insulate) are also staggered. 2 to 4 splices in all depending on whether board has them wired in series or parallel. |
|
|
matt123 |
Posted: Sat Sep 12, 2009 11:35 am Post subject: |
|
Thank you so very much for your help!
I took out the bulbs and using a magnifying glass found that they were both burned out. Ill try and measure the voltage on the circuit board tomorrow and try and source some new bulbs. |
|
|
jts1957 |
Posted: Sat Sep 12, 2009 7:59 am Post subject: |
|
Depends on if they're wired in parallel? or series? 4 wires/4-pin plug/socket, but can't see foils on the board it plugs into.
Regular lamps - if you have meter, unplug and test for continuity on each bulb - if both open put meter on AC Volts and CAREFULLY measure the same pairs of connections on the board/socket. If NO reading, try switching meter to DC Volts.
If you get a reading note it down. That will be very close to the Voltage of the bulbs. Amperage is usually 35mA or 70 mA. I'm assuming they're wired in parallel. (1 burnt out but you didn't take notice until the second failed.)
If you get NO reading AC or DC try to follow to where they end up in power supply area, probably open fuse/resistor. |
|
|
matt123 |
|
|
jts1957 |
Posted: Sat Sep 12, 2009 6:01 am Post subject: |
|
Can you shine a light from behind? You're sure it's a LED (not a grain of wheat type lamp)? Is it mounted on a board (location #) or wired in? |
|
|
matt123 |
Posted: Sat Sep 12, 2009 5:47 am Post subject: |
|
thanks for the reply yes it works fine otherwise.
Ive tried shining a light on it but it doesn't seem to display anything.
thanks |
|
|
jts1957 |
Posted: Sat Sep 12, 2009 5:21 am Post subject: |
|
You don't say if the unit works OK otherwise.
Most stereos with LCD displays that have a back light will work just fine without a backlight bulb. Just point a flashlight at display to read. |
|
|