Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs

Post a reply
Username
Subject
Message body Emoticons View more Emoticons	Font colour: Default Dark Red Red Orange Brown Yellow Green Olive Cyan Blue Dark Blue Indigo Violet White Black  Font size: Tiny Small Normal Large Huge Close Tags [quote="Anonymous"]Self-diagnosis Code Table (for CCD-TRV99) Repaired by | Block Function | Detailed Code | Symptom/State | Correction. _____C___:|_____21_____:|_____00_____| Condensation_| Remove the cassette, and insert it again after one hour. C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer C 2 1 0 0 Condensation. Remove the cassette, and insert it again after one hour. C 2 2 0 0 Video head is dirty. Clean with the optional cleaning cassette. C 2 3 0 0 Non-standard battery is used. Use the InfoLITHIUM battery. C 3 1 1 0 LOAD direction. Loading does not complete within specified time Load the tape again, and perform operations from the beginning. C 3 1 1 1 UNLOAD direction. Loading does not complete within specified time Load the tape again, and perform operations from the beginning. C 3 1 2 0 T reel side tape slacking when unloading. Load the tape again, and perform operations from the beginning. C 3 1 2 1 S reel side tape slacking when unloading. Load the tape again, and perform operations from the beginning. C 3 1 2 2 T reel fault Load the tape again, and perform operations from the beginning. C 3 1 2 3 S reel fault Load the tape again, and perform operations from the beginning. C 3 1 3 0 FG fault when starting capstan Load the tape again, and perform operations from the beginning. C 3 1 3 1 FG fault during normal capstan operations Load the tape again, and perform operations from the beginning. C 3 1 4 0 FG fault when starting drum Load the tape again, and perform operations from the beginning. C 3 1 4 1 PG fault when starting drum Load the tape again, and perform operations from the beginning. C 3 1 4 2 FG fault during normal drum operations Load the tape again, and perform operations from the beginning. C 3 1 4 3 PG fault during normal drum operations Load the tape again, and perform operations from the beginning. C 3 1 4 4 Phase fault during normal drum operations Load the tape again, and perform operations from the beginning. C 3 2 1 0 LOAD direction loading motor time-out Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 1 1 UNLOAD direction loading motor time- out Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 2 0 T reel side tape slacking when unloading. Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 2 1 S reel side tape slacking when unloading. Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 2 2 T reel fault Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 2 3 S reel fault Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 3 0 FG fault when starting capstan Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 3 1 FG fault during normal capstan operations Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 4 0 FG fault when starting drum Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 4 1 PG fault when starting drum Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 4 2 FG fault during normal drum operations Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 4 3 PG fault during normal drum operations Remove the battery or power cable, connect, and perform operations from the beginning. C 3 2 4 4 Phase fault during normal drum operations Remove the battery or power cable, connect, and perform operations from the beginning. E 6 1 0 0 Difficult to adjust focus (Cannot initialize focus.) Inspect the lens block focus reset sensor (Pin !» of CN551 of VC-195 board) when focusing is performed when the focus dial is rotated in the focus manual mode and the focus motor drive circuit (IC552 of VC-195 board) when the focusing is not performed. E 6 1 1 0 Zoom operations fault (Cannot initialize zoom lens.) Inspect the lens block zoom reset sensor (Pin @Á of CN551 of VC-195 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC552 of VC195 board) when zooming is not performed. E 6 2 0 0 Handshake correction function does not work well.(With pitch angular velocity sensor output stopped) Inspect pitch angular velocity sensor (SE451 of SE-74 board) peripheral circuits. E 6 2 0 1 Handshake correction function does not work well.(With yaw angular velocity sensor output stopped) Inspect yaw angular velocity sensor (SE452 of SE-74 board) peripheral circuits. ============================================================== Service Mode Display The service mode display shows up to six self-diagnosis codes shown in the past. Display Method While pressing the “STOP” key, set the switch from OFF to “VTR or PLAYER”, and continue pressing the “STOP” key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes. Switching of Backup No. By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time End of Display Turning OFF the power supply will end the service mode display. Note: The self-diagnosis display data will be backed up by the coin-type lithium battery. When this coin-type lithium battery is disconnected, the self-diagnosis data will be lost by initialization. example: 3C:31:11 3=backup number C=repaired by (customer) 31=block (reload the tape) 11=detailed code (UNLOAD direction. Loading timed out)[/quote]
Options HTML is OFF BBCode is ON Smilies are ON	Disable BBCode in this post Disable Smilies in this post

All times are GMT

Latest Service Manuals : Panasonic RQX01 sch panasonic • 5s-1 module B.W.D • IC2GA GAT GE serv Icom • 02gen NOKIA • Nikon FM-2 Repair Manual . Various • 5ServSoft NOKIA • bc857 HT Semiconductor • CR1710, 1720 & 1730 Dual • BIRD 8832 Termaline Coaxial Load Resisto • 2n6806 irf9230 International Rectifier •