Author |
Message |
handy4469 |
Posted: Wed Jan 09, 2008 12:47 am Post subject: Re: NEC PX42VM3G |
|
Hi, what part do you require for your plasma, let me know or even send me a photo, i have the same model which im willing to sell parts from, i also have a brand new set of silver speakers for this model, my e-mail address is handy4469@msn.com regards, ernie.
Pinkwell(guest) wrote: |
I'm trying to get a copy of the service manual for the Nec PX42VM3G
Plasma
Also does anyone know where to get spares for the above
Your help would greatly appreciated. At present it all seems impossible to get mine repaired.Luckily I found this site
Thanks
pinkwell |
|
|
|
_hcr_ |
Posted: Fri Oct 20, 2006 7:39 pm Post subject: Is it possible?? |
|
Is it possible to get a copy of the service manual for the Nec PX42VM3G
Plasma ? I have looked everywhere. Please Help me If you have it pleas mail me at peder.myhre@bluezone.no[/code] |
|
|
Emjay |
Posted: Mon Jul 31, 2006 5:09 pm Post subject: NEC PX-42VM3G/S service manual required |
|
Hello,
I wonder if anyone managed to obtain a service manual for the PX-42VM3 series plasma displays ?
Although we are authorised for many manufacturers, NEC (and Fujitsu for that matter) are really restrictive when it comes to service data for their products.
Will be willing to exchange any Pana / Hitachi / Sanyo / Sharp / JVC manuals etc as required for the NEC manual.
Cheers
MJ
PS: Email is emjay111_jennifer-anniston_@hotmail.com
Take Jennifer Anniston out before replying ! (anti-spam) |
|
|
Pinkwell |
Posted: Tue Feb 14, 2006 1:59 am Post subject: Nec PX42VM3G |
|
Hi Dooney
Sorry for the long delay in contacting you
I have eventually contacted NEC in Telford and was pleasantly suprised with the quote they gave me,after I delivered the plasma to the company itself to save some of the charges and will collect when ready.I now wish that I had contacted them in the first place. Suprised at the courtesy afforded me and the amount of help offered. I hope anyone reading this will go to them first as at least they will have the satisfaction to know what they are talking about. Mind you I also have to thank you for all the help you offered me through your generosity, and you were right
Thanks once again. You're the tops. A1
pinkwell |
|
|
Dooney0 |
Posted: Thu Jan 19, 2006 2:29 am Post subject: PX-42VM3G |
|
Hi Pinkwell,
Yes, NEC do all there own in house repairs and do not have a service network throughout the uk. Pretty much the same world wide with 3rd party service agents in selected countries.
So you have a nice drive to Telford to look forward to...
If they can obtain the parts you should be ok, the prices for plasma are rediculas all around. Still they are much better than LCD.
Best regards
Mike |
|
|
Pinkwell |
Posted: Thu Jan 19, 2006 1:56 am Post subject: Nec PX42VM3G |
|
hi Dooney
I sent Nec an e-mail asking them if they had any recommended repairers in the UK and if so could they please provide me with them
they replied that they do not have any authorised service centres in the UK and that all repairs are carried out by themselves. so now we know
I have contacted the number that they have given me. The charges frightened me, I suppose that they are for companies who just reclaim it and not ordinary lay people. Eventually we settled for us to take the Plasma by car to them. Pay the evaluation fee and then decide if we want the repair done (or scrap something that cost over £ 4000 and had just over 2 years use) after they have quoted a price. |
|
|
Dooney0 |
Posted: Wed Jan 18, 2006 5:33 am Post subject: PX-42VM3G |
|
Hi Pinkwell,
No problem, Im not sure regarding sourcing of the service manual. All i can tell you is that the service manual does not contain any material refering to the PDP module (Panel) only dirrect modular level replacement.
I was not aware that you needed an account with B & H to order parts but i guess this makes sense.
I can tell you that normally the fuses are ok, but the PCB underneath the heat syncs are normally the course of failure, also it might be worth checking the fusable resistors.
Best regards
Mike. |
|
|
Pinkwell |
Posted: Wed Jan 18, 2006 4:27 am Post subject: Nec PX42VM3G |
|
Hi dooney
sorry for the delay.
As regards the service account, my engineer asked to setup a service account with B & H about 3/4 months ago and followed up by writing to them with the request for a service account but to date has had no reply
He didn't want to check my plasma without a service manual. He showed me the board in front of the PWb board and it had, I think it was 3 fuses and none of them had blown.I don't know if that means anything I appreciate the fact that although he had all test equipment he didn't want to proceed without the manual. He's put the back onto the Plasma and returned it. When he or I can get a manual and if I haven't had it repaired by then I will get him to check it out. he said he heard of a site in America that supposed to have manuals.
regards
pinkwell |
|
|
Dooney0 |
Posted: Thu Jan 12, 2006 3:46 am Post subject: PX-42VM3G |
|
Hi Pinkwell,
I think that B & H is the only supply route for NEC parts within the UK, due to the fact that Pioneer only own R & D rights to the plasma display the prevision of spare parts is NEC's responsibility and Pioneer would not be able to help. In fact they probably would have no idea what a PX-42VM3G is due to the fact that Pioneer in the UK only deal with their own branded product. The prevision of spare parts for plasma & LCD is generally poor from company to company and is not limited to NEC this is due to the cost of the parts. I think it is likely that the parts will become available but the wheels do tend to grind slowly, did B & H ask you to set up a service account ??
Best regards
Mike. |
|
|
Pinkwell |
Posted: Wed Jan 11, 2006 11:39 pm Post subject: Nec PX42VM3G |
|
Hi Mike
Thanks for the information. My e-mail is palexander@screaming.net. would appreciate contact. How hard is it to get a Nec service account? and also the best way of going about it. My mate has been waiting ages. Are they the only ones that supply replacements? I'd be a bit choked if I can't get spares for my plasma its just about 3 years old. would Pioneer help with my requests?
Thanks for your time
regards
pinkwell |
|
|