Author |
Message |
Dearis. |
Posted: Wed Jun 27, 2018 8:16 am Post subject: my touch screen does not works |
|
I turn on my touch screen does not works but by remote only. Wich it mean I could not change any thing even Date. บาคาร่าออนไลน์ |
|
|
Justmanuals |
|
|
sunday Isaac |
Posted: Thu Oct 20, 2011 1:31 pm Post subject: technical help |
|
i'm Sunday Isaac i have sharp AR-5516S has code error H4 i dont understand why it has come pliz i needed your technical advice |
|
|
Guest |
Posted: Sat Feb 27, 2010 7:56 am Post subject: |
|
H4 00 Content Heat roller low temperature detection Detail When the fusing temperature is lower than 150C° after 55sec from the start of warming up. When the warming up complete temperature is not reached in 30sec from reaching 150C°. When the fusing temperature is lower than 100C° after 20sec from ready start. When the fusing temperature is lower than 145C° when printing." Cause Thermistor abnormality Heater lamp abnormality Thermostat abnormality Control PWB abnormality Check and remedy Use SIM 5-02 to check the heater lamp blinking operation. When the lamp blinks normally. Check the thermistor and its harness. Check the thermistor input circuit on the control PWB. When the lamp does not light up. Check for disconnection of the heater lamp and the thermostat. Check the interlock switch. Check the power PWB and the lamp control circuit on the MCU PWB. Use SIM 14 to clear the self diagnostic display. |
|
|
Guest |
Posted: Mon Feb 01, 2010 2:42 am Post subject: |
|
Try the simulation about 5 times if not. u have to check fusing unit. so disconnect the two cables, turn it off then disconnect the power reconnect the cables. |
|
|
Justmanuals |
|
|
Badereldin |
Posted: Mon Jan 11, 2010 8:40 pm Post subject: Re: About The Reset H4 error |
|
Badereldin wrote: | alexglobal wrote: | alpertevfik wrote: | heater lamp&fuse ( broken heater) RESET:clear -interrupt -0-interrupt and 14 start-15 start good luck | I try the same seqence but failed for the H4 error, any advice is there pls. send me. Thanks Alex | Well plz try the simulation about 5 times if not. u have to check fusing unit. so disconnect the two cables, turn it off then disconnect the power reconnect the cables put the power then on. so u have to do the simulation respectively.. | it is freely to contact me through [email protected] or +249 923611846 |
|
|
Badereldin |
Posted: Mon Jan 11, 2010 8:35 pm Post subject: Re: About The Reset H4 error |
|
alexglobal wrote: | alpertevfik wrote: | heater lamp&fuse ( broken heater) RESET:clear -interrupt -0-interrupt and 14 start-15 start good luck | I try the same seqence but failed for the H4 error, any advice is there pls. send me. Thanks Alex | Well plz try the simulation about 5 times if not. u have to check fusing unit. so disconnect the two cables, turn it off then disconnect the power reconnect the cables put the power then on. so u have to do the simulation respectively.. |
|
|
alexglobal |
Posted: Sun Dec 24, 2006 2:36 pm Post subject: About The Reset H4 error |
|
alpertevfik wrote: | heater lamp&fuse ( broken heater) RESET:clear -interrupt -0-interrupt and 14 start-15 start good luck | I try the same seqence but failed for the H4 error, any advice is there pls. send me. Thanks Alex |
|
|
alpertevfik |
Posted: Thu Jun 08, 2006 1:27 am Post subject: |
|
heater lamp&fuse ( broken heater) RESET:clear -interrupt -0-interrupt and 14 start-15 start good luck |
|
|