Guest |
Posted: Thu Nov 26, 2009 6:43 am Post subject: |
|
Self-diagnosis Code Table (for CCD-TRV99)
Repaired by | Block Function | Detailed Code | Symptom/State | Correction.
_____C___:|_____21_____:|_____00_____| Condensation_| Remove the cassette, and insert it again after one hour.
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service engineer
C 2 1 0 0 Condensation. Remove the cassette, and insert it again after one hour.
C 2 2 0 0 Video head is dirty. Clean with the optional cleaning cassette.
C 2 3 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
C 3 1 1 0 LOAD direction. Loading does not
complete within specified time
Load the tape again, and perform operations from the beginning.
C 3 1 1 1 UNLOAD direction. Loading does not
complete within specified time
Load the tape again, and perform operations from the beginning.
C 3 1 2 0 T reel side tape slacking when unloading. Load the tape again, and perform operations from the beginning.
C 3 1 2 1 S reel side tape slacking when unloading. Load the tape again, and perform operations from the beginning.
C 3 1 2 2 T reel fault Load the tape again, and perform operations from the beginning.
C 3 1 2 3 S reel fault Load the tape again, and perform operations from the beginning.
C 3 1 3 0 FG fault when starting capstan Load the tape again, and perform operations from the beginning.
C 3 1 3 1 FG fault during normal capstan operations Load the tape again, and perform operations from the beginning.
C 3 1 4 0 FG fault when starting drum Load the tape again, and perform operations from the beginning.
C 3 1 4 1 PG fault when starting drum Load the tape again, and perform operations from the beginning.
C 3 1 4 2 FG fault during normal drum operations Load the tape again, and perform operations from the beginning.
C 3 1 4 3 PG fault during normal drum operations Load the tape again, and perform operations from the beginning.
C 3 1 4 4 Phase fault during normal drum operations Load the tape again, and perform operations from the beginning.
C 3 2 1 0 LOAD direction loading motor time-out
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 1 1 UNLOAD direction loading motor time-
out
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 2 0 T reel side tape slacking when unloading.
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 2 1 S reel side tape slacking when unloading.
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 2 2 T reel fault
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 2 3 S reel fault
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 3 0 FG fault when starting capstan
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 3 1 FG fault during normal capstan operations
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 4 0 FG fault when starting drum
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 4 1 PG fault when starting drum
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 4 2 FG fault during normal drum operations
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 4 3 PG fault during normal drum operations
Remove the battery or power cable, connect, and perform operations
from the beginning.
C 3 2 4 4 Phase fault during normal drum operations
Remove the battery or power cable, connect, and perform operations
from the beginning.
E 6 1 0 0 Difficult to adjust focus
(Cannot initialize focus.)
Inspect the lens block focus reset sensor (Pin !» of CN551 of VC-195
board) when focusing is performed when the focus dial is rotated in the
focus manual mode and the focus motor drive circuit (IC552 of VC-195
board) when the focusing is not performed.
E 6 1 1 0 Zoom operations fault
(Cannot initialize zoom lens.)
Inspect the lens block zoom reset sensor (Pin @Á of CN551 of VC-195
board) when zooming is performed when the zoom lens is operated and
the zoom motor drive circuit (IC552 of VC195 board) when zooming is
not performed.
E 6 2 0 0 Handshake correction function does not
work well.(With pitch angular velocity
sensor output stopped)
Inspect pitch angular velocity sensor (SE451 of SE-74 board) peripheral
circuits.
E 6 2 0 1 Handshake correction function does not
work well.(With yaw angular velocity
sensor output stopped)
Inspect yaw angular velocity sensor (SE452 of SE-74 board) peripheral
circuits.
==============================================================
Service Mode Display
The service mode display shows up to six self-diagnosis codes shown in the past.
Display Method
While pressing the “STOP” key, set the switch from OFF to “VTR or PLAYER”, and continue pressing the “STOP” key for 5 seconds
continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time [4] : Occurred fourth time
[2] : Occurred second time [5] : Occurred fifth time
[3] : Occurred third time [6] : Occurred the last time
End of Display
Turning OFF the power supply will end the service mode display.
Note: The self-diagnosis display data will be backed up by the coin-type lithium battery. When this coin-type lithium battery is
disconnected, the self-diagnosis data will be lost by initialization.
example: 3C:31:11
3=backup number
C=repaired by (customer)
31=block (reload the tape)
11=detailed code (UNLOAD direction. Loading timed out) |
|