| Author |
Message |
| DMW649 |
 Posted: Sun Sep 14, 2008 1:39 am Post subject: |
|
Well I finally was able to do the repair on this set. I ordered the wrong caps at first. I ordered the diode type, reordered the correct ones. Replaced the caps Minnie recommended and also cleaned up the area on the board. It was hard to see the leaking crt fluid on the board, until I had the chassic out for repair. Removed and soldered the 4 new caps back and reconnected everything. Fired it up and all systems are go!!!! I added a piece of cardboard over the area where the leaking crt is, don't know if it will help. All I know is that surgery went well and if I come upon the problem in the future I can do the same repair. Want to thank Minnie for your expert advice you made my day  . Thanks Dennis |
|
 |
| minnie |
| Posted: Tue Aug 19, 2008 4:18 am Post subject: |
|
| DMW649 wrote: | Minnie- Thanks for your help and fast reply. Dennis  |
Thank me when it's fixed.  |
|
|
| DMW649 |
| Posted: Tue Aug 19, 2008 4:09 am Post subject: |
|
| Minnie- Thanks for your help and fast reply. Dennis |
|
|
| minnie |
| Posted: Mon Aug 18, 2008 8:17 pm Post subject: |
|
| All the problems are from the same caps. |
|
|
| DMW649 |
| Posted: Mon Aug 18, 2008 2:05 pm Post subject: Minnie-Quick Question Before I Do Repair On Mitsubishi VS507 |
|
| Hi Minnie- TV worked fine for a month now it has a little different problem. The set comes on sound and picture fine then a loud popping sound and a horizontal 2-3" line appears on the screen. Happens a couple times a minute. Error code is still 12. Do you think this is still the same problems involving the caps? I purchased the ones you said I needed to replace- C2PO2-47m/35v, C2PO3-100m/16v, C2PO4-47m/16v and C2PO5-100m/16v on the signal board. Would like to do this repair once. Do you think I need any other parts other than caps listed above. Thanks Dennis |
|
|
| DMW649 |
| Posted: Wed Jul 16, 2008 1:11 pm Post subject: |
|
| Minnie- Thanks for your help. I'll keep you posted after I change the caps. Thanks, Dennis |
|
|
| minnie |
| Posted: Mon Jul 14, 2008 10:15 pm Post subject: |
|
| Anonymous wrote: | | I ordered the parts from Ness. The next day went to take a look at the set and to prepare for surgery, while awaiting the ordered parts. Set now working fine showing no prior problems. I'll just have to postpone surgery for now, go figure! |
The caps are 'dry' already. When it comes back replace them and you'll be fine. |
|
|
| Guest |
| Posted: Mon Jul 14, 2008 7:10 pm Post subject: |
|
| I ordered the parts from Ness. The next day went to take a look at the set and to prepare for surgery, while awaiting the ordered parts. Set now working fine showing no prior problems. I'll just have to postpone surgery for now, go figure! |
|
|
| minnie |
| Posted: Fri Jul 11, 2008 11:38 pm Post subject: |
|
| I use Ness electronics or just go to a place that fixes tv's and ask them to sell them to you. Unplug the set and you'll be fine. |
|
|
| DMW649 |
| Posted: Fri Jul 11, 2008 10:48 pm Post subject: Mitsubishi 50705 Projection TV Picture goes to black screen |
|
Minnie- Thanks for this info and fast reply. Couple of quick questions. Any good place to p/u these parts. Also any area inside the set to stay clear of, don't want to get juiced  Thanks, Dennis |
|
|