[sparky]

Snap! My wife also bought me a Sony DVD recorder for transfering tapes from video and camcorder. I have been doing this for a couple of days now and didn't realise I had so many.

Happy New Year to all

[Guest]

Sparky

Thanks for your valuable advice which should keep my VCR up and running while I archieve my VHS tapes of family events to DVD using my Sony 710 Christmas box.

Regards and Best Wishes for the New Year

DaveH

[sparky]

Sorry the capacitor location is in the power supply (mixed with a sharp model).

[sparky]

This bracket was fitted at the rear of the drum assembly.

[sparky]

Trying to remember the deck used in this machine as been out of the trade a few years now (memory going a signe of old age) but seem to recall a small bracket that was fitted between the chassis and pcb that was too short and Toshiba supplied a longer one as a modification to improve the earthing. The symptoms were white noise dots on playback.
If I didn't have a bracket I tinned the copper part on the pcb and soldered.
Another part that caused noise problems was electrolytic capacitor C051 1uF, 50V on the lower drum pcb leaking and eating away the print. The cure was to remove, repair the print and replace the capacitor (I just used a miniture 105 degree type). Also have a look at the capstan pulley ensuring it does not have a split. If it was split I Removed and fitted a metal one supplied for Mitsubishi with a little glue.
The drum may have a bit of friction if it mangled a tape on rewind but if it becomes a problem you could polish it with brasso while being careful not to clog the heads.
This is purely memory so it may be poss I may be getting confused with another as you can appreciate the amount of makes and models of equipment a service department obtain for repair.
I still have quite a few spare parts and may have this bracket but remember ordering several and obtaining the original type instead which was of little use. A lack of communication between Toshiba spares and technical department perhaps.

[Guest]

Grtz Mark, Sparky

Thanks for your help.

No sign of the head cleaner sponge roller - the Toshiba service agent must have concluded that its more trouble than its worth, or simply been out of stock etc.

Heads guide posts, tension posts, idle rollers etc cleaned, plus load / reload tracks for guide and tension pins cleaned and lubricated.

A couple of worrying moments when it unwound (and ruined) a cassette into the head area durign a load, but after extracating the casette power-lead removal reset the load cam OK.

VCR now works noise free (with the lid off) with auto track correcting system working properly at last.

Curiously playback noise levels are significantly higher with the case lid replaced. All earth tags etc cleaned but I cant locate the exact cause. Guess its an earth loop problem or similar.

Regards

DaveH.

[sparky]

The head cleaner roller normally has a spong attached to the plastic roller that can become dirty and cause more harm than good by actually making the heads dirty. I would have thought Toshiba would have replaced it though.

[Al_Dodge_Bundy]

The head cleaner roller, should make contact with the video head, whenever you eject a tape (or push the cleaning button on your VCR (if available) for a short time.

But if you already cleaned the heads properly, a none functioning head cleaner, will not be your problem.

[Guest]

Grtz Mark, Sparky


I have had a careful look at the inside of the VCR and I am puzzled by the Head Cleaner at the rear of the Cylinder Assembly.

The Head Cleaner Roller Sub-Assembly seems to consist of a simple white U-shaped hard-plastic bobbin that never makes contact with the Head

Is this the roller sub assembly, or has something been left off when the VCR was last serviced by Toshiba ?

Regards

David H.

[sparky]

Ensure correct movement of tape (not riding up and down on the control head or entry/exit guides) and the entry/exit guides are going fully home in the play mode. If o.k then try head switching point adjustment.

Happy New Year