View previous topic :: View next topic |
Author |
Message |
ftast
Joined: 10 Sep 2007 Posts: 1
|
Posted: Mon Sep 10, 2007 8:22 am Post subject: acer al1711 main board. |
|
|
does anybody know where i can get a logic board for an acer al1711 monitor?
the only place i could find one was in Sweden. When i power it on it rotates colors so i think the controller chip is bad. The power switch doesn't work. When you plug it in its on and stays on. |
|
Back to top |
|
|
bicycle6228 Guest
|
Posted: Sun Feb 10, 2008 6:28 pm Post subject: acer al1711 pwr supply board resistor value |
|
|
I have resistor R1 on this board that is burned beyond recognition. It is located in the back light inverter area, just below the small green fuse F1 and just to the left of coil L856. If anyone has access to one of these boards and could read me the color band sequence / resistance value I'd surely appreciate it. Thanks. |
|
Back to top |
|
|
4ltrv1sm0
Joined: 29 Apr 2008 Posts: 5
|
Posted: Tue Apr 29, 2008 6:25 am Post subject: |
|
|
to ftast:
I have my logic board in good conditions, but i dont see what you say, if you make a photo ill try to help you.
my issue:
my monitor switchs on and stays it (my power switch doesnt work), ive maked it work in a way: plugin partially the bus cable that feeds the control board from de p-supply unit, but it looks green then in the top of the screen. when i did it i could use it, so its a logic trouble. how could i fix that?
thanks a lot! _________________ Check out my Recording Studio!
www.grabacionesfatuas.com |
|
Back to top |
|
|
blueoutcast Guest
|
Posted: Fri Jul 25, 2008 9:45 pm Post subject: |
|
|
Hey altrv1smo,
Can you get the picture of the power board in the AL1711, I need the same picture of the resistor that the others are looking for. Very important. Thanks |
|
Back to top |
|
|
SZASZ
Joined: 27 Apr 2007 Posts: 69 Location: TIMISOARA
|
Posted: Thu Aug 14, 2008 9:05 am Post subject: |
|
|
Hello,
Try to enter factory mode and torn off "BURN IN MODE", if you don't find any board to replace it. |
|
Back to top |
|
|
4ltrv1sm0
Joined: 29 Apr 2008 Posts: 5
|
Posted: Thu Jan 29, 2009 3:41 pm Post subject: |
|
|
Working again with the screen. Ill post a photo as soon as I can.
The Acer service manual about this model, said in the connector CN852 pin #6 there must be 12v and I only have 5.
Anyone more? _________________ Check out my Recording Studio!
www.grabacionesfatuas.com |
|
Back to top |
|
|
4ltrv1sm0
Joined: 29 Apr 2008 Posts: 5
|
Posted: Thu Jan 29, 2009 3:43 pm Post subject: |
|
|
By the way, how can I enter to factory mode? _________________ Check out my Recording Studio!
www.grabacionesfatuas.com |
|
Back to top |
|
|
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
Posted: Thu Jan 29, 2009 3:53 pm Post subject: |
|
|
You have the service manual. It does not tell you how? |
|
Back to top |
|
|
Guest
|
Posted: Thu Jan 29, 2009 5:29 pm Post subject: |
|
|
Havent looked for it, can it fix issues like these? |
|
Back to top |
|
|
4ltrv1sm0
Joined: 29 Apr 2008 Posts: 5
|
Posted: Thu Jan 29, 2009 5:31 pm Post subject: |
|
|
Missed to login, sorry _________________ Check out my Recording Studio!
www.grabacionesfatuas.com |
|
Back to top |
|
|
|
|