electronics, repairs, service manuals and datasheets discussion community for the repairs professionals and technicians
FAQSearchMembersGroupsRegisterProfilePM'sLogin/Out
Spectroniq PLTV-3250 wont start

 
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs
View previous topic :: View next topic  
Author Message
Xtech
Guest





PostPosted: Wed Feb 04, 2009 5:10 am    Post subject: Spectroniq PLTV-3250 wont start Reply with quote

Hello
I am working with a spectroniq (proton) model PLTV-3250
LCD TV. The set will not start I found a series of bad electrolytic
capacitors in the power supply along with a small
surface mount transistor, all of which I have replaced.
The front standby light is not lit. It uses an FSP194-3F01 power supply.
I have not been able to round up any service data for this unit.
And they dont appear to have a website anywhere on the net.
I need to know at what points in the supply I should be receiving
voltage and how much. There is a noise that's barely audible coming
from the top area of the set, I think its one of the boards that control
the LCD panel lights, but I'm not 100 percent sure.

Just curious if anyone has (or knows) where I can get a manual,
and help steer me in the right direction.

Thank you
Back to top
vtech



Joined: 08 May 2006
Posts: 1264
Location: USA

PostPosted: Wed Feb 04, 2009 5:51 am    Post subject: Reply with quote

Only thing I know that it was not made by Proton---it was Protron Digital which filed for chapter 11 on 08. No idea about the manual though?
Back to top
View user's profile Send private message
Xtech
Guest





PostPosted: Wed Feb 04, 2009 4:36 pm    Post subject: Reply with quote

I sent an Email to FSP (the manufacturer of the power supply)
and requested a schematic. I’ll see how cooperative they are.
Back to top
Xtech
Guest





PostPosted: Tue Feb 17, 2009 10:19 pm    Post subject: Reply with quote

Update:
The company who makes the supply wouldn't supply a schematic.
I found a new power supply and replaced it.
Back to top
hacker gnome
Guest





PostPosted: Fri Feb 20, 2009 5:25 am    Post subject: FSP194-3F01 Reply with quote

xtech, Where did you find a power supply?
Thanks
Back to top
Xtech
Guest





PostPosted: Tue Feb 24, 2009 11:16 pm    Post subject: Re: FSP194-3F01 Reply with quote

hacker gnome wrote:
xtech, Where did you find a power supply?
Thanks


Ebay,

I was able to repair the old one.
After doing some comparison testing between the
two. I found a zener diode that was killing the 5 volt
standby voltage. It was neither shorted or open. It
originally tested good in circuit using diode check on my DMM.
Back to top
[email protected]
Guest





PostPosted: Thu Dec 09, 2010 9:06 pm    Post subject: 5 volts stand by missing Reply with quote

i have work in this tv proton for several times and i never hane any problem with the 5 volts stand by but always found a cap bad on 5 stby after replaced the caps if any vary has still problems with 5 volts stby chek ZD4 its close to the IC2its reading bad after you replaced this zener diode power will work 5 volts stand by missing
Back to top
nowone
Guest





PostPosted: Wed Jan 19, 2011 12:16 pm    Post subject: zener Reply with quote

What is the voltage for the zener diode?
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs All times are GMT
Page 1 of 1

 
Jump to:  
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


eServiceInfo on FB - Service Manuals Free Download - Service Diagrams

Free TV Schematics Download - HARDW.net - Pinout Master - Jabse Service Manual Search - Jabse.InK  - onTap.bg

SnimkiOt.com - Poblizo.com : пътешествия