View previous topic :: View next topic |
Author |
Message |
leafar
Joined: 15 Mar 2007 Posts: 42
|
Posted: Fri May 29, 2009 3:51 am Post subject: |
|
|
jts1957 wrote: | I assume there is NO AUDIO either. Any Blinking timer light code?
Could be anything from a B-Plus source being missing, the T-Chip (TV processing all in one I.C. - may be CXA series) has a defect, something affecting the communication (I2C) bus between Tuner/micro/EEPROM/T-Chip.
Without a schematic or at least IC numbers ... |
CXA1446s IC ive seen it near the tuner. for ur info sir when tv is on i tried to put the tip of my finger on top of that IC ,its cold. could it be possible that it has no DC supply on it? i dont want to try to test it when the unit is on to avoid short ckt . |
|
Back to top |
|
|
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
|
Back to top |
|
|
leafar
Joined: 15 Mar 2007 Posts: 42
|
Posted: Fri May 29, 2009 4:06 am Post subject: |
|
|
jts1957 wrote: | I assume there is NO AUDIO either. Any Blinking timer light code?
Could be anything from a B-Plus source being missing, the T-Chip (TV processing all in one I.C. - may be CXA series) has a defect, something affecting the communication (I2C) bus between Tuner/micro/EEPROM/T-Chip.
Without a schematic or at least IC numbers ... |
Its a CXA1446S IC near the tuner sir,more than 10 blinks,no audio ,only the raster sound heard. TV is on-put the tip of my finger on top of that IC,its cold. Its like no DC supply coming in the IC. |
|
Back to top |
|
|
leafar
Joined: 15 Mar 2007 Posts: 42
|
Posted: Fri May 29, 2009 4:17 am Post subject: |
|
|
thanks for your help sir... |
|
Back to top |
|
|
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
Posted: Fri May 29, 2009 4:34 am Post subject: |
|
|
Quote: | could it be possible that it has no DC supply on it? i dont want to try to test it when the unit is on to avoid short ckt . |
Find the pin on the IC you want to measure. Follow the foil trace away from the IC to another solder joint on same foil trace. You can either measure at this new point or if you're "shaky," you could solder on a pigtail and attach to that.
Pin 1 (V. Reg.) wants 6.8 volt - Pin 15 (VCC) wants 9 volts. |
|
Back to top |
|
|
Guest
|
Posted: Fri May 29, 2009 5:07 am Post subject: |
|
|
jts1957 wrote: | Quote: | could it be possible that it has no DC supply on it? i dont want to try to test it when the unit is on to avoid short ckt . |
Find the pin on the IC you want to measure. Follow the foil trace away from the IC to another solder joint on same foil trace. You can either measure at this new point or if you're "shaky," you could solder on a pigtail and attach to that.
Pin 1 (V. Reg.) wants 6.8 volt - Pin 15 (VCC) wants 9 volts. |
Noted sir,thanks again...i will give you feedback after ive done checking the Ic. |
|
Back to top |
|
|
minnie
Joined: 18 Aug 2005 Posts: 2880 Location: Hell
|
Posted: Sun May 31, 2009 10:08 pm Post subject: |
|
|
If it has osd and no picture I'd replace the jungle ic. |
|
Back to top |
|
|
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
Posted: Sun May 31, 2009 10:27 pm Post subject: |
|
|
Not a "jungle" IC as we are used to.
VIF/SIF is in above IC. I presume Video/OSD/Chroma/Def, etc. is in (at least) 2nd IC.
Even if this 2nd chip is the cause shouldn't he still be getting sound? |
|
Back to top |
|
|
leafar
Joined: 15 Mar 2007 Posts: 42
|
Posted: Mon Jun 01, 2009 5:18 am Post subject: |
|
|
jts1957 wrote: | Not a "jungle" IC as we are used to.
VIF/SIF is in above IC. I presume Video/OSD/Chroma/Def, etc. is in (at least) 2nd IC.
Even if this 2nd chip is the cause shouldn't he still be getting sound? |
Thanks to both of you minnie & jts1957 for the reply, eventhough my tv is a vintage unit, i want to learn more ideas how to repair tv`s. With your help in this forum ,i`ve learned a lot with you guys. I wanted this tv to be repaired bec. its my dad gift on my my wedding day.
Let`s move again to our fault finding, i already replaced the CXA IC ,the unit have the sound output but the pic is not good, the pic has black vertical line like partition in the middle, the image is not in centered position ,image is devided into two portions in slant S position,the half from left portion went to right and the right image went to left . any idea sirs? Is this a CRT problem sir? |
|
Back to top |
|
|
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
Posted: Mon Jun 01, 2009 6:27 am Post subject: |
|
|
jts1957 wrote: | Pin 1 (V. Reg.) wants 6.8 volt - Pin 15 (VCC) wants 9 volts. |
Did you ever get around to measuring these on the CXA1446S? |
|
Back to top |
|
|
|
|