electronics, repairs, service manuals and datasheets discussion community for the repairs professionals and technicians
FAQSearchMembersGroupsRegisterProfilePM'sLogin/Out
error H4 sharp 5316 AR-Digital Copier
Goto page 1, 2  Next
 
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Computer and office equipment repairs
View previous topic :: View next topic  
Author Message
Maikle
Guest





PostPosted: Sat May 06, 2006 11:03 pm    Post subject: error H4 sharp 5316 AR-Digital Copier Reply with quote

Please can some1 kindly tell me how to cure a falshin error "H4" on the sharp AR5316??? I know its a sequence of buttons on the screen

Thank you
Back to top
alpertevfik



Joined: 08 Jun 2006
Posts: 9

PostPosted: Thu Jun 08, 2006 1:27 am    Post subject: Reply with quote

heater lamp&fuse ( broken heater)
RESET:clear -interrupt -0-interrupt
and 14 start-15 start
good luck
_________________
alp
Back to top
View user's profile Send private message MSN Messenger
alexglobal
Guest





PostPosted: Sun Dec 24, 2006 2:36 pm    Post subject: About The Reset H4 error Reply with quote

alpertevfik wrote:
heater lamp&fuse ( broken heater)
RESET:clear -interrupt -0-interrupt
and 14 start-15 start
good luck


I try the same seqence but failed for the H4 error, any advice is there pls.
send me. Thanks
Alex
Back to top
Badereldin
Guest





PostPosted: Mon Jan 11, 2010 8:35 pm    Post subject: Re: About The Reset H4 error Reply with quote

alexglobal wrote:
alpertevfik wrote:
heater lamp&fuse ( broken heater)
RESET:clear -interrupt -0-interrupt
and 14 start-15 start
good luck


I try the same seqence but failed for the H4 error, any advice is there pls.
send me. Thanks

Alex

Well plz try the simulation about 5 times if not. u have to check fusing unit. so disconnect the two cables, turn it off then disconnect the power reconnect the cables put the power then on. so u have to do the simulation respectively..
Back to top
Badereldin
Guest





PostPosted: Mon Jan 11, 2010 8:40 pm    Post subject: Re: About The Reset H4 error Reply with quote

Badereldin wrote:
alexglobal wrote:
alpertevfik wrote:
heater lamp&fuse ( broken heater)
RESET:clear -interrupt -0-interrupt
and 14 start-15 start
good luck


I try the same seqence but failed for the H4 error, any advice is there pls.
send me. Thanks

Alex

Well plz try the simulation about 5 times if not. u have to check fusing unit. so disconnect the two cables, turn it off then disconnect the power reconnect the cables put the power then on. so u have to do the simulation respectively..

it is freely to contact me through [email protected] or +249 923611846
Back to top
Justmanuals



Joined: 21 Aug 2004
Posts: 1948

PostPosted: Mon Jan 11, 2010 9:26 pm    Post subject: Reply with quote

This Parts & Service manual can now be purchased for $11.77 and downloaded immediately after payment from http://www.justmanuals.com


[email protected]
_________________
Want To Fix Something?
http://www.manuals4you.com

Need a manual now? Instant Download
http://www.justmanuals.com
Back to top
View user's profile Send private message Send e-mail
Guest






PostPosted: Mon Feb 01, 2010 2:42 am    Post subject: Reply with quote

Try the simulation about 5 times if not. u have to check fusing unit. so disconnect the two cables, turn it off then disconnect the power reconnect the cables.
Back to top
Guest






PostPosted: Sat Feb 27, 2010 7:56 am    Post subject: Reply with quote

H4 00 Content Heat roller low temperature detection
Detail When the fusing temperature is lower than
150C° after 55sec from the start of warming
up.
When the warming up complete temperature is
not reached in 30sec from reaching 150C°.
When the fusing temperature is lower than
100C° after 20sec from ready start.
When the fusing temperature is lower than
145C° when printing."
Cause Thermistor abnormality
Heater lamp abnormality
Thermostat abnormality
Control PWB abnormality
Check
and
remedy
Use SIM 5-02 to check the heater lamp blinking
operation.
When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the control
PWB.
When the lamp does not light up.
Check for disconnection of the heater lamp and
the thermostat. Check the interlock switch.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use SIM 14 to clear the self diagnostic display.
Back to top
sunday Isaac
Guest





PostPosted: Thu Oct 20, 2011 1:31 pm    Post subject: technical help Reply with quote

i'm Sunday Isaac i have sharp AR-5516S has code error H4 i dont understand why it has come pliz i needed your technical advice
Back to top
Justmanuals



Joined: 21 Aug 2004
Posts: 1948

PostPosted: Thu Oct 20, 2011 3:20 pm    Post subject: Reply with quote

This Parts & Service manual can now be purchased for $12.77 and downloaded immediately after payment from

http://www.justmanuals.com


[email protected]
_________________
Want To Fix Something?
http://www.manuals4you.com

Need a manual now? Instant Download
http://www.justmanuals.com
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Computer and office equipment repairs All times are GMT
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


eServiceInfo on FB - Service Manuals Free Download - Service Diagrams

Free TV Schematics Download - HARDW.net - Pinout Master - Jabse Service Manual Search - Jabse.InK  - onTap.bg

SnimkiOt.com - Poblizo.com : пътешествия