View previous topic :: View next topic |
Author |
Message |
beertap
Joined: 04 Jan 2011 Posts: 22
|
Posted: Tue Jan 04, 2011 6:21 pm Post subject: Hitachi Television Dead |
|
|
I have a Hitachi 46F500A projection television that has a "clicking noise" similar to a turn signal on a car with a red LED on front panel blinking at same rate. It will continue to cycle on and off. When the unit comes on, just for the split second it does, it has a raster then cycles off only to turn back on again. Any ideas? or common replacement part(s)? Thanks. |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
rturner76
Joined: 04 Jan 2011 Posts: 4
|
Posted: Wed Jan 05, 2011 12:13 am Post subject: |
|
|
Sounds like the convergence chips have quit working. They are usually located on the main board, attached to a large heat-sink. They are black, about the size of a small cellular phone and are marked "STK-###". If you have any soldering skills you should be able to replace them yourself. You can find a kit at www.tvrepairkits.com. They also include a step by step instruction on how to replace them. |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
Posted: Wed Jan 05, 2011 12:14 am Post subject: |
|
|
Convergence or power supply most likely. _________________ You're over there, I'm over here. |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
beertap
Joined: 04 Jan 2011 Posts: 22
|
Posted: Wed Jan 05, 2011 1:48 am Post subject: |
|
|
I have taken the connector "PPD5" off. It goes to the deflection. The power supply board's 5 green LEDs and 1 red LED will come on and stay on with this connector off. Just trying to narrow down cause since I don't remember seeing any convergence problems as the screen looked pretty sharp before it died. |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
beertap
Joined: 04 Jan 2011 Posts: 22
|
Posted: Tue Jan 11, 2011 12:13 am Post subject: |
|
|
I have replaced the convergence chips with no luck. Any other ideas? |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
Posted: Tue Jan 11, 2011 1:12 am Post subject: |
|
|
I'd wonder about the B-Plus to the HOT running too high since you said the raster comes on for a short time.
Any heavy load could cause the set to attempt to turn on, sense it has a overload and then shut off. _________________ You're over there, I'm over here. |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
beertap
Joined: 04 Jan 2011 Posts: 22
|
Posted: Tue Jan 11, 2011 1:15 am Post subject: |
|
|
Also, I can unplug one of the vertical/horizontal deflection yokes on either three tubes and the power supply will stay on. |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
Posted: Tue Jan 11, 2011 2:24 am Post subject: |
|
|
That would imply vertical. H windings in parallel - V windings in series. _________________ You're over there, I'm over here. |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
beertap
Joined: 04 Jan 2011 Posts: 22
|
Posted: Tue Jan 11, 2011 2:56 am Post subject: |
|
|
"That would imply vertical. H windings in parallel - V windings in series." That is true.
B+ should be 115v but measured 116.3v. I noticed on QH01 (H.V. OUT) that the drain measured 330v but it should be 255.6v. |
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
beertap
Joined: 04 Jan 2011 Posts: 22
|
|
Back to top |
|
![](templates/subVereor/images/spacer.gif) |
|
|