View previous topic :: View next topic |
Author |
Message |
Jason Guest
|
Posted: Sun Mar 12, 2006 2:18 am Post subject: Sony KV29F2U FLASHES TWICE |
|
|
Hello All,
My Sony TV screen goes blank soon as i switch it on then goes to standby then flashes twice.
Does anyone now the cause of this?? What component(s) need replacing?
Thanks in advance.
Jason |
|
Back to top |
|
|
william chueng Guest
|
Posted: Sun Mar 12, 2006 10:02 am Post subject: Re: Sony KV2972U |
|
|
Jason wrote: | Hello All,
My Sony TV screen goes blank soon as i switch it on then goes to standby then flashes twice.
Does anyone now the cause of this?? What component(s) need replacing?
Thanks in advance.
william | |
|
Back to top |
|
|
gary
Joined: 05 Apr 2005 Posts: 584 Location: MANCHESTER, uk
|
Posted: Mon Mar 13, 2006 7:45 pm Post subject: |
|
|
2 flashes on that model is over current protection, check to see if line output transistor is short circuit. if so replace it and check for dry joints on line drive tx, if line transistor fails again at switch on replace line output transformer. |
|
Back to top |
|
|
Guest
|
Posted: Wed Mar 15, 2006 6:59 am Post subject: |
|
|
Thanks Gary for your reply, would you know which component it is..I am ok replacing items with a soldering Iron but not so good at locating them.
Thanks in advance
Jason |
|
Back to top |
|
|
gary
Joined: 05 Apr 2005 Posts: 584 Location: MANCHESTER, uk
|
Posted: Wed Mar 15, 2006 5:42 pm Post subject: |
|
|
line output transistor is Q802 mounted on a heatsink at the back of pcb, line output transformer is T803, line drive transformer is T804. |
|
Back to top |
|
|
Guest Guest
|
Posted: Wed Apr 26, 2006 9:22 pm Post subject: Part numbers |
|
|
Hello,
Q802 has finaly benn replaced but still no joy.. Picture comes on for few seconds then goes into standby and flashes twice. Looking for the part numbers for the line output drive transformer (T804) and line output transformer (T803). Does anyone now what they are??
Thanks in advance.
Jason |
|
Back to top |
|
|
gary
Joined: 05 Apr 2005 Posts: 584 Location: MANCHESTER, uk
|
Posted: Wed Apr 26, 2006 9:42 pm Post subject: |
|
|
BEFORE REPLACING LOPTX, REMOVE CRT BASE AND TURN SET ON, IF THE SET RUNS HAPPILY THE FAULT COULD BE THE CURRENT MONITORING RESISTOR IN THE PSU, I THINK IT IS R608 A 0.47R, ITS VALUE IS CRITICAL AND ONLY NEEDS RO RISE TO ABOUT 0.7R TO CAUSE THE FAULT YOU DESCRIBE, REPLACE IT DON'T MEASURE IT UNLESS METER IS VERY ACCURATE. |
|
Back to top |
|
|
Guest
|
Posted: Sun May 07, 2006 4:52 am Post subject: |
|
|
Hello Gary,
R608 has been replaced (0.47ohm) still goes into standby and flashes twice. When open circuit R608 the the TV seems to work normally, but i see no picture/sound. Short circuit R608 - fault returns.
Any way to bypass the protection??
Thanks in adavance.
Jason |
|
Back to top |
|
|
Guest
|
Posted: Sat May 20, 2006 12:38 am Post subject: |
|
|
Hello all,
Anything else i can try on this TV....seems so close to the problem.
The radio is not as entertaining..
Thanks in advance
Jason |
|
Back to top |
|
|
jovino Guest
|
Posted: Sun May 21, 2006 9:13 am Post subject: i have a similar problem... |
|
|
I have a Sony Triniatron, model KV-24FS100. The diagnostic light also blinks twice.
I could not locate any of the transistors mentioned in this thread (there are no circuits in the 800 range on the main circuitboard), so I tested all of the heat-sinked transistors and it looks like Q506 (D2634 / 2G3) located close to the H-Out section is testing kinda funny. Does this make sense?
I'm not the most adept at this stuff, so please excuse my ignorance. And thanks to y'all for this thread. |
|
Back to top |
|
|
|
|