electronics, repairs, service manuals and datasheets discussion community for the repairs professionals and technicians
FAQSearchMembersGroupsRegisterProfilePM'sLogin/Out
philips l01.1e

 
Post new topic   This topic is locked: you cannot edit posts or make replies.    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs
View previous topic :: View next topic  
Author Message
terminator2k2



Joined: 29 Apr 2005
Posts: 1

PostPosted: Fri Apr 29, 2005 3:51 pm    Post subject: philips l01.1e Reply with quote

hi all just wandering if some one could help me.?? i have a philips 32pw6006, it uses the L01.1e chassis. problem is from cold the set will switch on and after 10 or so seconds , the set will switch off , but not into standby. if i keep pressing the channel up/down buttons the set will remain on and stay on, but what would cause it to shut down after 10 secs.?? i think it may be the tube.???
Back to top
View user's profile Send private message
qbsystems
Guest





PostPosted: Sat Apr 30, 2005 9:04 am    Post subject: Re: philips l01.1e Reply with quote

terminator2k2 wrote:
hi all just wandering if some one could help me.?? i have a philips 32pw6006, it uses the L01.1e chassis. problem is from cold the set will switch on and after 10 or so seconds , the set will switch off , but not into standby. if i keep pressing the channel up/down buttons the set will remain on and stay on, but what would cause it to shut down after 10 secs.?? i think it may be the tube.???


This fault is cause by c2455 in the line drive replace with 105oC type as original is 85oC
Back to top
Guest






PostPosted: Tue May 03, 2005 7:25 pm    Post subject: Reply with quote

hi there thanks for your reply, i changed that cap and also adjusted the a1 as per service manual with a scope to no avail... i have now got 3 sets with the same fault, 2 x 32s and 1x 28.
Back to top
mark



Joined: 20 Jan 2005
Posts: 43

PostPosted: Thu May 05, 2005 5:26 am    Post subject: Reply with quote

you losing hv?
i know phillips had issues with some micros on some sets that caused weird problems.
the fact that you have 3 makes me wonder tho, red flag there.
Back to top
View user's profile Send private message
Guest






PostPosted: Thu May 05, 2005 7:27 pm    Post subject: Reply with quote

loseing hv.?? what do you mean by that.?? i know the a10 chassis suffers from micro probs, but ive neever changed one on this chassis. its also displaying fault code 11 in service mode, wich says check the rgb output, so ive ordered a couple to see what difference that makes. i still think it might be duff tubes though as its only faulty from cold and there are no voltage variations or picture/sound faults before the sets go off.
Back to top
Eam
Guest





PostPosted: Mon May 09, 2005 7:58 pm    Post subject: L01 Reply with quote

Hi
I have had 2 l01s with this problem, sorry to say both sets the CRT was the cause one boosted clear the other did not.
Regards Eam
Back to top
Display posts from previous:   
Post new topic   This topic is locked: you cannot edit posts or make replies.    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs All times are GMT
Page 1 of 1

 
Jump to:  
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Електроника София - Service Manuals Free Download - Prikachi - Service Diagrams

Free TV Schematics Download - HARDW.net - Pinout Master - Jabse Search - Jabse.InK  - Pulsator

Connector Pinout Forum - Новини - SnimkiOt.com - безплатен DNS - Whois разузнаване - Poblizo.com : пътешествия