electronics, repairs, service manuals and datasheets discussion community for the repairs professionals and technicians
FAQSearchMembersGroupsRegisterProfilePM'sLogin/Out
philip 55pp9401 convergence
Goto page Previous  1, 2, 3, 4, 5  Next
 
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Electronics General
View previous topic :: View next topic  
Author Message
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Sat Aug 23, 2008 12:07 pm    Post subject: Reply with quote

Replace the STK392-110's. Could be STK392-150's. Resister values:
Resistor Location Value Part #
RK42 3.3 Ω 1 W AT03202S
RK46 1.8 Ω 1 W AT03195S
RK50 3.3 Ω 1 W AT03202S
RK54 1.8 Ω 1 W AT03195S
RK58 3.9 Ω 1 W AT03204S
RK62 2.2 Ω 1 W AT03197S
IK04 & IK05 STK394-160E CZ01341

STK394-160's are the newest replacement.
Back to top
View user's profile Send private message Send e-mail
Guest






PostPosted: Mon Sep 01, 2008 7:25 pm    Post subject: Reply with quote

minnie wrote:
Replace the STK392-110's. Could be STK392-150's. Resister values:
Resistor Location Value Part #
RK42 3.3 Ω 1 W AT03202S
RK46 1.8 Ω 1 W AT03195S
RK50 3.3 Ω 1 W AT03202S
RK54 1.8 Ω 1 W AT03195S
RK58 3.9 Ω 1 W AT03204S
RK62 2.2 Ω 1 W AT03197S
IK04 & IK05 STK394-160E CZ01341

STK394-160's are the newest replacement.

I really have no clue what those part numbers are representing, could I just take a pic of the board and you tell me which ones to replace?
Are these Radio Shack parts or somewhere else?
Thanks.
Mark
Back to top
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Fri Sep 12, 2008 7:59 pm    Post subject: Reply with quote

If you'd register I could send you a pdf file that shows you.
Back to top
View user's profile Send private message Send e-mail
PIXER



Joined: 21 Sep 2008
Posts: 1
Location: KY

PostPosted: Sun Sep 21, 2008 1:23 am    Post subject: Reply with quote

minnie wrote:
If you'd register I could send you a pdf file that shows you.

DONE, AND THANK YOU
Back to top
View user's profile Send private message
iwannafixit



Joined: 19 Dec 2008
Posts: 1

PostPosted: Fri Dec 19, 2008 4:41 pm    Post subject: hithach 43fdx20b Reply with quote

I have bad resistors on the dp1x convergence pwb board, does anyone have the value of the resistors for this board next to the ic's.
Thanks.
Back to top
View user's profile Send private message
aaronjwithrow



Joined: 28 Dec 2008
Posts: 1

PostPosted: Sun Dec 28, 2008 9:30 pm    Post subject: Green Convergance issue on 55pp9401 Board Reply with quote

I recently picked up a used set from a co-worker. It was working great for about 10 minutes then the Green appears to be bowed down from the top and up from the bottom. the image looks like it is concave.. you cannot adjust the convergence by using the service mode.
We DO know the issue is on the convergence board - if you swap with blue it follows..

so the question.. It has 2 STK-392-110IC/s It is a DP1X convergence pwb. what are the resister values.. there are 2 that are very difficult to read..
Back to top
View user's profile Send private message
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Mon Dec 29, 2008 10:11 pm    Post subject: Re: Green Convergance issue on 55pp9401 Board Reply with quote

aaronjwithrow wrote:
I recently picked up a used set from a co-worker. It was working great for about 10 minutes then the Green appears to be bowed down from the top and up from the bottom. the image looks like it is concave.. you cannot adjust the convergence by using the service mode.
We DO know the issue is on the convergence board - if you swap with blue it follows..

so the question.. It has 2 STK-392-110IC/s It is a DP1X convergence pwb. what are the resister values.. there are 2 that are very difficult to read..


Ask justmanuals if he has a schematic. Phillips dropped tech support.
Back to top
View user's profile Send private message Send e-mail
freezen3535



Joined: 31 Dec 2008
Posts: 1

PostPosted: Wed Dec 31, 2008 4:21 am    Post subject: Convergence philips 55pp9401 Reply with quote

Hi there Minnie, After reading many of these posts, you seem to be the one to help me the most. I have a philips 55pp9401 with a convergence problem. The Chassis # on back says its a pp15. Where can I get the correct Ics and resistors to make a repair. Thanks in advance for any help you can give. Very Happy
Back to top
View user's profile Send private message
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Thu Jan 01, 2009 6:56 pm    Post subject: Reply with quote

http://www.matelectronics.com/
Back to top
View user's profile Send private message Send e-mail
awtoys



Joined: 31 Jan 2009
Posts: 1

PostPosted: Sat Jan 31, 2009 7:11 pm    Post subject: Reply with quote

Thank minnie, ichage the stk. but i not sure the value resistors, one of then reading 42 ohms, other 17 and when verify the other circuit the resistor are very low.
_________________
www.awtoys.net
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Electronics General All times are GMT
Goto page Previous  1, 2, 3, 4, 5  Next
Page 4 of 5

 
Jump to:  
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


eServiceInfo on FB - Service Manuals Free Download - Service Diagrams

Free TV Schematics Download - HARDW.net - Pinout Master - Jabse Service Manual Search - Jabse.InK  - onTap.bg

SnimkiOt.com - Poblizo.com : пътешествия