| View previous topic :: View next topic |
| Author |
Message |
DMW649
Joined: 10 Jul 2008
Posts: 11
|
 Posted: Thu Jul 10, 2008 4:03 am Post subject: Mitsubishi 50705 Projection TV Picture goes to black screen |
 |
|
Set is 8 years old. Service code is 1-2. Sound and channels are good. Picture comes on then black broken lines appear and run across the screen then picture goes black. Few seconds and does it all over again. Need some help with where to start to correct this, and parts to check and or replace. Thanks, also p/u a service manual so let the fun begin.  |
|
| Back to top |
|
 |
minnie
Joined: 18 Aug 2005
Posts: 2880
Location: Hell
|
| Posted: Thu Jul 10, 2008 11:33 pm Post subject: |
|
|
| 12 is no problem. Replace C2P02-47m/35v, C2P03-100m/16v, C2P04-47m/16v, C2p05-100m/16v on the signal board. |
|
| Back to top |
|
|
DMW649
Joined: 10 Jul 2008
Posts: 11
|
| Posted: Fri Jul 11, 2008 10:48 pm Post subject: Mitsubishi 50705 Projection TV Picture goes to black screen |
|
|
Minnie- Thanks for this info and fast reply. Couple of quick questions. Any good place to p/u these parts. Also any area inside the set to stay clear of, don't want to get juiced  Thanks, Dennis |
|
| Back to top |
|
|
minnie
Joined: 18 Aug 2005
Posts: 2880
Location: Hell
|
| Posted: Fri Jul 11, 2008 11:38 pm Post subject: |
|
|
| I use Ness electronics or just go to a place that fixes tv's and ask them to sell them to you. Unplug the set and you'll be fine. |
|
| Back to top |
|
|
Guest
|
| Posted: Mon Jul 14, 2008 7:10 pm Post subject: |
|
|
| I ordered the parts from Ness. The next day went to take a look at the set and to prepare for surgery, while awaiting the ordered parts. Set now working fine showing no prior problems. I'll just have to postpone surgery for now, go figure! |
|
| Back to top |
|
|
minnie
Joined: 18 Aug 2005
Posts: 2880
Location: Hell
|
| Posted: Mon Jul 14, 2008 10:15 pm Post subject: |
|
|
| Anonymous wrote: | | I ordered the parts from Ness. The next day went to take a look at the set and to prepare for surgery, while awaiting the ordered parts. Set now working fine showing no prior problems. I'll just have to postpone surgery for now, go figure! |
The caps are 'dry' already. When it comes back replace them and you'll be fine. |
|
| Back to top |
|
|
DMW649
Joined: 10 Jul 2008
Posts: 11
|
| Posted: Wed Jul 16, 2008 1:11 pm Post subject: |
|
|
| Minnie- Thanks for your help. I'll keep you posted after I change the caps. Thanks, Dennis |
|
| Back to top |
|
|
DMW649
Joined: 10 Jul 2008
Posts: 11
|
| Posted: Mon Aug 18, 2008 2:05 pm Post subject: Minnie-Quick Question Before I Do Repair On Mitsubishi VS507 |
|
|
| Hi Minnie- TV worked fine for a month now it has a little different problem. The set comes on sound and picture fine then a loud popping sound and a horizontal 2-3" line appears on the screen. Happens a couple times a minute. Error code is still 12. Do you think this is still the same problems involving the caps? I purchased the ones you said I needed to replace- C2PO2-47m/35v, C2PO3-100m/16v, C2PO4-47m/16v and C2PO5-100m/16v on the signal board. Would like to do this repair once. Do you think I need any other parts other than caps listed above. Thanks Dennis |
|
| Back to top |
|
|
minnie
Joined: 18 Aug 2005
Posts: 2880
Location: Hell
|
| Posted: Mon Aug 18, 2008 8:17 pm Post subject: |
|
|
| All the problems are from the same caps. |
|
| Back to top |
|
|
DMW649
Joined: 10 Jul 2008
Posts: 11
|
| Posted: Tue Aug 19, 2008 4:09 am Post subject: |
|
|
| Minnie- Thanks for your help and fast reply. Dennis |
|
| Back to top |
|
|
|
|
|
FAQ
