electronics, repairs, service manuals and datasheets discussion community for the repairs professionals and technicians
FAQSearchMembersGroupsRegisterProfilePM'sLogin/Out
Need help on a Plasma Grundig planatron pw 110-520/9

 
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs
View previous topic :: View next topic  
Author Message
weltradio



Joined: 09 Nov 2008
Posts: 3

PostPosted: Sun Nov 09, 2008 11:29 am    Post subject: Need help on a Plasma Grundig planatron pw 110-520/9 Reply with quote

Folks,
Issue is a very famous fault on this Plasma: Picture disappears and screen stays black, after rebooting the same game.
My knowledge so far:
My 180 and 60 V misses a short time after boot up.
This may take a short or a long time but not more than 10 minutes.
The panel has now a total of 3500 hours, picture is very well.
The plasma is on my desk and its opened for troubleshooting.
I saw that the big power supply which is located in the middle of the TV has the following feature:
small plug from digi board: Power supply on/off, by pulling this plug I can start the big supply manually.
right red plug: 180 and 60 Volt out
left red plug: 5V out, 3 signals from the panel: 1.5, 2.0 and 3 Volt DC.
It doesnt matter if the power supply is switching off, these feedback lines are not changing and there is no RF signal on it at any case, just the DC.
My panel works good,(if its supplied of course) and I do not understand the reason that the power supply is switching off..
I suppose its doing a current out measurement and when its over the limit its protecting the panel or what ever and switches off.
Do you think I am on the right way ?

Hope anyone investigated more time in this fail for helping all the other guys who have the same fail on this wonderful plasma !!
Best regards from Germany,
TOM
Back to top
View user's profile Send private message Send e-mail
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Sun Nov 09, 2008 8:12 pm    Post subject: Reply with quote

Check your VS/VA voltages listed on the panel. Disconnect the X any Y sustain boards. If you disconnect them and your VS and VA come up you have a bad panel. If they don't, suspect power supply.
Back to top
View user's profile Send private message Send e-mail
weltradio



Joined: 09 Nov 2008
Posts: 3

PostPosted: Mon Nov 10, 2008 7:13 am    Post subject: VS//VA Reply with quote

Hi minnie,

THX a lot!!
VS/VA: These are the voltages which come out from the power supply at the backward, the +180V and the 60 V, RIGHT ?
(this power lines goes directly to the electronic to the panel)
X and Y driver: This are the big power boards at the left and the right side of the panel with the big black cooling units ?
Just disconnect them and see if the voltages 60/180 stay good in this CASE ?

Best regards,
Tom
Back to top
View user's profile Send private message Send e-mail
weltradio



Joined: 09 Nov 2008
Posts: 3

PostPosted: Tue Nov 25, 2008 4:53 pm    Post subject: Questio: Reply with quote

Will the power supply be damaged if I disconnect the panel ?
I mean, will the output voltage raise up immediately and it destroys itself ?
I can remember the very first old switching poer supply always needs a load to work ??
best regards
Thomas
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs All times are GMT
Page 1 of 1

 
Jump to:  
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


eServiceInfo on FB - Service Manuals Free Download - Service Diagrams

Free TV Schematics Download - HARDW.net - Pinout Master - Jabse Service Manual Search - Jabse.InK  - onTap.bg

SnimkiOt.com - Poblizo.com : пътешествия