View previous topic :: View next topic |
Author |
Message |
Bob_in_OKC
Joined: 16 Oct 2009 Posts: 3
|
Posted: Fri Oct 16, 2009 1:45 am Post subject: AC synchronous motors |
|
|
Many stereo turntables - record players - are driven by a small AC synchronous motor. It's a magnet on a spindle, rotating inside a two-piece shell. So my question is simple - Is such a motor supposed to have oil in it? |
|
Back to top |
|
|
vtech
Joined: 08 May 2006 Posts: 1264 Location: USA
|
Posted: Fri Oct 16, 2009 2:57 am Post subject: |
|
|
There is no need or requirement to have oil inside an electric motor.
If you see any signs, it is from the end bearings that support the shaft. |
|
Back to top |
|
|
Bob_in_OKC
Joined: 16 Oct 2009 Posts: 3
|
Posted: Fri Oct 16, 2009 4:02 am Post subject: |
|
|
Thanks very much for the reply. Could you tell me why the motor would develop a grinding noise that starts after around two hours of use? If so...what could be done to repair that? |
|
Back to top |
|
|
vtech
Joined: 08 May 2006 Posts: 1264 Location: USA
|
Posted: Sat Oct 17, 2009 5:14 am Post subject: |
|
|
Strictly depends on your application and type of motor; In general, the "grinding" noise is normally caused by dried lubricant or worn out bearings &/or bushings supporting the spinning armature on either end of the housing.
If it is a sealed motor, chances of a reliable repair is slim to none. You may be able to buy some time by applying a drop of lubricating oil at the base of the drive shaft, allowing it to work it's way in--it may help. If it is a brush-type, generally it is best to replace rather than repair.
If it can be disassembled, barring from worn out bearings, dismantling and clean and re-lubing shaft/bearings is the way to go. |
|
Back to top |
|
|
Bob_in_OKC
Joined: 16 Oct 2009 Posts: 3
|
Posted: Sat Oct 17, 2009 5:43 am Post subject: |
|
|
The motor does open...quite easily, in fact. I can pop it open by twisting a screwdriver in one of the slots on the edge. Inside the two halves is a spinning cylindrical magnet with a spindle that serves as the drive shaft. The bottom of the shaft sits on a ball bearing. The top of the shaft goes out through the top half of the motor and drives the belt. With the idea it's that shaft, I've dropped oil in the bottom, where the ball bearing is. So far so good. Thanks for the help. |
|
Back to top |
|
|
|
|
|
You can post new topics in this forum You can reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
eServiceInfo on FB -
Service Manuals Free Download -
Service Diagrams
Free TV Schematics Download -
HARDW.net -
Pinout Master -
Jabse Service Manual Search -
Jabse.InK -
onTap.bg
SnimkiOt.com -
Poblizo.com : пътешествия
Latest Service Manuals :
14bsh4 NOKIA • Adj Di181 076 Minolta • HP DV2000 [Akita,Wistron] notebook sch . • VE710-2 Series SB 015 Viewsonic • bfp183r Siemens • Sansui-TU-555-Schematic Philips • 2sk879 Toshiba • hfe pioneer sx-1300 2300 service Pioneer • FAN7601 OZL68GN - L1752S, L1952S chassis • MO-1230 C&C INSTRUMENTS •
|