electronics, repairs, service manuals and datasheets discussion community for the repairs professionals and technicians
FAQSearchMembersGroupsRegisterProfilePM'sLogin/Out
Samsung S5033 Plasma Problem

 
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs
View previous topic :: View next topic  
Author Message
Bailey22
Guest





PostPosted: Sun Mar 28, 2010 1:10 am    Post subject: Samsung S5033 Plasma Problem Reply with quote

Model: HP-S5033, Model Code: HPS5033X/XAA, Type: CD50P7
Initial problem: loss picture sound was ok.
I found a 6.3A fuse blown (F5002) on the 50'HD W1 Y-MAIN (Model No on board, not sure if that is really a hyphen) PCB Code: LJ41-04516A.
I replaced the fuse.
Now the Stand-by turns on and off. (relay pulls in then releases)
All caps look good.
The power supply board is a Model PSPF501A01A.
I disconnected a harness that goes to another board which connects to the X-Main & Y-Main. PSB relay continues to cycle on & off.
There's another board behind the board where all the Ant. cable, HDMI, component cables connect (Model Porsche/Cadillac, that's what it says) that is connected to the PSU board with led that flash on and off with the relay cycle.
When I disconnect this board from the PSU, I hear the relay click only once and the led on the power button, on the front of the tv, flashes 4 times and goes out. Note: this other board also connects to the X-Main & Y-Main boards through ribbon cables (not sure how to disconnect these).

I sure hope someone can help me out here.

Steve
Back to top
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Sun Mar 28, 2010 11:39 pm    Post subject: Reply with quote

What happens if you disconnect the Y sustain board?
Back to top
View user's profile Send private message Send e-mail
Bailey22
Guest





PostPosted: Mon Mar 29, 2010 1:51 am    Post subject: Reply with quote

Minnie,
I unplugged the Y sustain board and the same thing occured.
Note: there is a ribbon cable connected to the Y-Main board that I haven't tried to disconnect. Can't really tell how it snaps in, didn't want to break it. If I need to disconnect it I'll figure it out. The main power plug is disconnected though.

A little more specifics as to what is happening not posted above.
I mentioned a board I can't see straight on. I can tell that there are two green LEDs that light when the relay energizes(I hear the click). About 4 seconds latter a third green LED flashes 4 times and all LEDs go out along with the relay de-energizing. 2 seconds later the relay energizes the LEDs come back on and the cycle starts over.

Thanks for your interest and help.

Steve
Back to top
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Mon Mar 29, 2010 6:02 pm    Post subject: Reply with quote

Have you disconnected the Y and X and no change? Have you disconnected the bottom buffer boards or the Y sustain driver boards?
Back to top
View user's profile Send private message Send e-mail
Guest






PostPosted: Sat Apr 03, 2010 5:24 pm    Post subject: Reply with quote

minnie,
I found another fuse blown. Thought I had check everything. I waited to reply until I got new fuses.
It's the 5A fuse on the PS board.
I inserted a new fuse and and plugged it in the fuse blew immediately. I had the plug feeding the X&Y boards unplugged.
It looks like the PS board has a short somewhere. The board is pretty busy and checking diodes while in place is not reliable. DO you have any suggestion?

Thanks
Steve
Back to top
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Sat Apr 03, 2010 6:16 pm    Post subject: Reply with quote

I's suspect the Y sustain took out the power supply. My guess is a bad panel took out the Y sustain. I think you're looking at a bad panel. BN96-03290A subs to a BN96-03290 list about $600 plus a $500 core.
Back to top
View user's profile Send private message Send e-mail
Justmanuals



Joined: 21 Aug 2004
Posts: 1948

PostPosted: Sun Apr 04, 2010 12:24 am    Post subject: Reply with quote

This Parts & Service manual can now be purchased for $10.77 and downloaded immediately after payment from http://www.justmanuals.com


[email protected]
_________________
Want To Fix Something?
http://www.manuals4you.com

Need a manual now? Instant Download
http://www.justmanuals.com
Back to top
View user's profile Send private message Send e-mail
Guest






PostPosted: Sun Apr 04, 2010 2:26 am    Post subject: Reply with quote

minnie,
That sounds as bad as it gets. Makes sense though. Is there away to test the panel to verify what you suspect?

Thanks for the help,

Steve
Back to top
minnie



Joined: 18 Aug 2005
Posts: 2880
Location: Hell

PostPosted: Thu Apr 08, 2010 12:45 am    Post subject: Reply with quote

Not really. If you unplu boards and it comes on, you can narrow it down to that board. Seems you've unplugged all the boards and the set hasn't stayed on.
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Electronic equipment repair and service manual search discussion Forum Index -> Equipment Repairs All times are GMT
Page 1 of 1

 
Jump to:  
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


eServiceInfo on FB - Service Manuals Free Download - Service Diagrams

Free TV Schematics Download - HARDW.net - Pinout Master - Jabse Service Manual Search - Jabse.InK  - onTap.bg

SnimkiOt.com - Poblizo.com : пътешествия