| View previous topic :: View next topic |
| Author |
Message |
ohfishing
Joined: 08 Mar 2009
Posts: 4
Location: ohio usa
|
 Posted: Sun Mar 08, 2009 9:24 pm Post subject: RCA d52w19 |
 |
|
Hello, I bought the crappy rca , only 3 years old , walmart special...
the power light was coming on blinking 3 times , and the set would shut off.
I found these help websites and started reading .
I decided my problem was the fly back, and a cap. My cap # 150 was bulged out at the top slightly so I did remove it
I looked over all the rest of the board and found no more bad caps
I bought the flyback and cap , removed the old ones, and today soldered in the new flyback and #150 cap
I hit the power and the tv works !!!
However I had a "fuzzy" picture that was hour glassed shaped
After inspecting the board, I found a ribbon cable that I must have bumped , which had come out ao I shut down the power and I reseated it, and on power up the tv became near perfect
HOWEVER (again lol) I still have a problem (small one)
whenever there is words on the screen, they are fuzzy and behind the letters in the word is another letter, in red
Its like the words are written over themselves and the underlying word is in red
I hope I described that ok , i guess what im trying to say is....
I read up , I got the correct parts , I soldered them in.... im this close to my kids having 52" spongebob , and its a little fuzzy , and I dont want to put it back together until its darn near perfect
does anyone know what could be the probelem?
The whole picture is a little out of focus (not bad) and the words have a red shadow
_________________
Ohio Fishing reports www.ohfishing.com |
|
| Back to top |
|
 |
minnie
Joined: 18 Aug 2005
Posts: 2880
Location: Hell
|
| Posted: Sun Mar 08, 2009 9:35 pm Post subject: |
|
|
| Check the fuse FL231 near the flyback you replaced. |
|
| Back to top |
|
|
ohfishing
Joined: 08 Mar 2009
Posts: 4
Location: ohio usa
|
| Posted: Sun Mar 08, 2009 10:29 pm Post subject: fuses |
|
|
Minnie I was hoping you would help me, I checked all 3 of the fuses in that area , all 3 have the spring looking fuse intact
my wife noticed the poor solder on one of the flyback pins, and I resoldered it, and on power up it was LITTLE BETTER
the red letter shadow was alot smaller but still there , also the picture got a little better also, its almost near perfect , i hope i can fix this my little ones are praying for a fix!
_________________
Ohio Fishing reports www.ohfishing.com |
|
| Back to top |
|
|
ohfishing
Joined: 08 Mar 2009
Posts: 4
Location: ohio usa
|
| Posted: Sun Mar 08, 2009 10:40 pm Post subject: |
|
|
I went into setup menu and I do have the CONVERGENCE option (i have been reading up)
_________________
Ohio Fishing reports www.ohfishing.com |
|
| Back to top |
|
|
minnie
Joined: 18 Aug 2005
Posts: 2880
Location: Hell
|
| Posted: Sun Mar 08, 2009 10:40 pm Post subject: |
|
|
| Have you gone into the customer menu and touched up the convergence? |
|
| Back to top |
|
|
ohfishing
Joined: 08 Mar 2009
Posts: 4
Location: ohio usa
|
| Posted: Sun Mar 08, 2009 10:56 pm Post subject: |
|
|
ran auto converg and the set is fixed !!!!!!!!!!!!!!!
thank you !!!!!!!!
you made a little girl REAL HAPPY!
_________________
Ohio Fishing reports www.ohfishing.com |
|
| Back to top |
|
|
minnie
Joined: 18 Aug 2005
Posts: 2880
Location: Hell
|
| Posted: Sun Mar 08, 2009 11:00 pm Post subject: |
|
|
| ohfishing wrote: | ran auto converg and the set is fixed !!!!!!!!!!!!!!!
thank you !!!!!!!!
you made a little girl REAL HAPPY! |
That's what were here for!  |
|
| Back to top |
|
|
Guest
|
| Posted: Fri Jan 01, 2010 5:23 am Post subject: |
|
|
minnie .... I hope your still here !!
Looks like I have to replace this flyback again 
I paid $17 1 year ago to fix it
i dont even have the part # anymore nor do i remember where I bought it
how could this part break again! |
|
| Back to top |
|
|
minnie
Joined: 18 Aug 2005
Posts: 2880
Location: Hell
|
| Posted: Fri Jan 01, 2010 10:45 pm Post subject: |
|
|
| Anonymous wrote: | minnie .... I hope your still here !!
Looks like I have to replace this flyback again
I paid $17 1 year ago to fix it
i dont even have the part # anymore nor do i remember where I bought it
how could this part break again! |
What's the full model and ctc #? |
|
| Back to top |
|
|
guest55
Guest
|
| Posted: Sat Feb 06, 2010 6:44 am Post subject: flyback # |
|
|
the model # is
D52W19
The chassis # is
ITC222
The model service # is
D52W19BYX1 |
|
| Back to top |
|
|
|
|
|
FAQ
