View previous topic :: View next topic |
Author |
Message |
bk-67 Guest
|
Posted: Wed May 30, 2012 10:06 pm Post subject: Clarion PN2715N |
|
|
Hi!
I'm looking for a servicemanual to an clarion built radio CD player. Model PN2715N. Mounted in a Nissan Navara.
The owner connected by misstake, when charging the battery, 24V into the car system. And only the radio CD player stopped working. Seems to me that the mecanical in the CD changer is working. (I can hear it)
Before changing the complete unit to a similar and expensive model he asked me as a technician to check it out.
I have opend the case and found a few burned components on the power unit on the PCB board. I have also identified and changed these components. But it will not work out at all. Anyone knowing where to find a manual to this radio unit.
Best regards
Benny
BK electronic |
|
Back to top |
|
|
voivoda
Joined: 23 Jun 2004 Posts: 63
|
|
Back to top |
|
|
Kaczus
Joined: 19 Aug 2014 Posts: 8 Location: POLAND
|
Posted: Wed Aug 20, 2014 7:36 pm Post subject: Re: Clarion PN2715N |
|
|
Hello!
Guys help!
I have a problem with the original changer Nissan Clarion PN-2715N [CD6k-1400E]. When I put the newly recorded disc system threw me the message "DISK READ ERROR". I thought that the problem lies in the dirty laser lens - the car is from 2008. After demolition and careful cleaning of the lens clean with isopropanol and reassembly I noticed that the drive I boot from the disc, lens flashes but does not illuminate (no beam of light)... I stripped again checked the tape drive, I cleaned, I made - no effect....
I thought it was a laser ... this is the SONY KSS-660 / KSS-662, both look the same ... today after a month when the package arrived with a new laser switched it ... the effect is the same .... help! |
|
Back to top |
|
|
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
Posted: Wed Aug 20, 2014 8:37 pm Post subject: |
|
|
You DID remove the shipping shorting strip after installation? _________________ You're over there, I'm over here. |
|
Back to top |
|
|
Kaczus
Joined: 19 Aug 2014 Posts: 8 Location: POLAND
|
Posted: Sat Aug 23, 2014 7:32 am Post subject: |
|
|
It's about removing the solder with a laser? He was not in the two lasers as soon as I opened the package?
|
|
Back to top |
|
|
jts1957
Joined: 24 Nov 2008 Posts: 2476 Location: Far, Far Away
|
|
Back to top |
|
|
Kaczus
Joined: 19 Aug 2014 Posts: 8 Location: POLAND
|
|
Back to top |
|
|
Kaczus
Joined: 19 Aug 2014 Posts: 8 Location: POLAND
|
Posted: Sat Aug 30, 2014 5:04 am Post subject: |
|
|
No one help?? |
|
Back to top |
|
|
Kaczus
Joined: 19 Aug 2014 Posts: 8 Location: POLAND
|
Posted: Wed Sep 10, 2014 2:07 pm Post subject: |
|
|
hallo ?? |
|
Back to top |
|
|
Kaczus
Joined: 19 Aug 2014 Posts: 8 Location: POLAND
|
Posted: Sat Nov 08, 2014 12:49 pm Post subject: |
|
|
Up?? |
|
Back to top |
|
|
|
|