View previous topic :: View next topic |
Author |
Message |
ollie2009uk
Joined: 07 Feb 2010 Posts: 2
|
Posted: Sun Feb 07, 2010 10:42 am Post subject: Panasonic TH42PX80BA |
|
|
Hi all,
Can someone offer some suggestions as to what this fault may be?
The unit is out of warranty so I just wanted to know if its even worth getting it repaired?
I have attached a picture of the problem.
Thanks
[/img] |
|
Back to top |
|
|
The_AntiRAM Guest
|
Posted: Sun Feb 07, 2010 9:02 pm Post subject: |
|
|
Pull out screws and open the back, provide detailed photo of the internal
circuitry.
Furthermore try to find printed Panel manufacturer and Code/Version. |
|
Back to top |
|
|
Justmanuals
Joined: 21 Aug 2004 Posts: 1948
|
|
Back to top |
|
|
gary
Joined: 05 Apr 2005 Posts: 584 Location: MANCHESTER, uk
|
Posted: Mon Feb 08, 2010 9:35 am Post subject: |
|
|
the fault is caused by a defective pdp, even though the unit is out of warranty take the set to a Panasonic DSN member with the original receipt, ask them to contact panasonic for you to request repair assistance, i would be very suprised if they do not repair it as a "goodwill gesture". |
|
Back to top |
|
|
eduard0476
Joined: 07 Feb 2010 Posts: 7 Location: philipines
|
Posted: Mon Feb 08, 2010 12:04 pm Post subject: some tips |
|
|
HI!! just check the power inverter on the side with CCFL attached... hope this can help... post and update when you done... _________________ "TECHNICAL ANSWER!!! |
|
Back to top |
|
|
gary
Joined: 05 Apr 2005 Posts: 584 Location: MANCHESTER, uk
|
Posted: Mon Feb 08, 2010 1:01 pm Post subject: |
|
|
cant be the inverter assy connected to the ccfl because the set is a plasma tv not lcd and does not use ccfl |
|
Back to top |
|
|
minnie
Joined: 18 Aug 2005 Posts: 2881 Location: Hell
|
Posted: Tue Feb 09, 2010 4:19 am Post subject: |
|
|
Looks like a bad buffer board to me! Could be the panel also but worth a sot! C1 C2 are usualy the designation. |
|
Back to top |
|
|
gary
Joined: 05 Apr 2005 Posts: 584 Location: MANCHESTER, uk
|
Posted: Tue Feb 09, 2010 9:19 am Post subject: |
|
|
never had a buffer board fail on that model, have changed 32 of the pdps used in that series of plasmas. as you can tell not reliable, many of those were "goodwill repairs", apparently the foam used to prevent dust ingress can release a gas when first new that gradually eats away at the ribbons to the pdp, usually causes single lines or groups but i have seen several with the same fault, if you dont have the receipt try the buffer as minnie suggests but i dont hold out much hope. |
|
Back to top |
|
|
ollie2009uk
Joined: 07 Feb 2010 Posts: 2
|
Posted: Tue Feb 09, 2010 8:03 pm Post subject: |
|
|
Thanks guys, if you think its a buffer board can you get them on ebay? |
|
Back to top |
|
|
The_AntiRAM Guest
|
Posted: Wed Feb 10, 2010 7:38 pm Post subject: |
|
|
ollie2009uk wrote: | Thanks guys, if you think its a buffer board can you get them on ebay? |
YES YOU CAN.
But, did you read what Gary wrote ?? |
|
Back to top |
|
|
|
|