Date | Header | Text |
15-02-2009 | Sony KLV-S26A10E not displaying red??? | Hi, hope somebody can help me out here. I've been given the a Sony KLV-S26A10E LCD television but the screen is not displaying any red, makes the screen look like it has a blueish hue.
Any ideas what could be wrong with it and can it be fixed? Ideally |
15-02-2009 | | Yes it is the same with either signal type. Any ideas? Thank you for your reply. This problem is driving me batty. |
15-02-2009 | SONY BVS-3200CP VIDEO SWITCHER SERVICE MANUAL | PLEASE PL PL. HELP
I NEED SERVICE MANUAL FOR SONY VIDEO SWITCHER MODEL NUMBER-
SONY BVS-3200CP THANK UUUUUUUUUUUUUUUU
[email protected] |
15-02-2009 | Daewoo CM915 No Picture Problem | Hi
I have a PARS TV with a chasis of CM915, I think It is Daewoo
Here the Schematic
http://www.4shared.com/file/87846048/11b79109/CM9151.html
(Upload it in ur site if there isn't any)
The Problem with that is there is No picture and sound while |
16-02-2009 | Re: HP LCD Monitor 1530 Green pwr light no Display | [quote:ab98607dd7="minnie"][quote:ab98607dd7="evox121"]I just recently had the same problem with this monitor.
But after finding this post im back up and running. The pico fuse was my prob.
Thx[/quote:ab98607dd7]
You should replace the caps anyways |
16-02-2009 | | Does EEPROM have 5 volts? Are filaments lit? |
16-02-2009 | | Thank U veru much
The +5V On EEPROM Is Okay
The Filament also Lit (+130V OK)
Is it possible anything wrong with ABL? The Voltage on Pin 22 of Video Processor (I501 Page 5) is going Up More than 3V; Is it natural?
ThanX
Shahriar |
16-02-2009 | | Looks like (Q802) 14volts stand by supplies 8 volt stand by and 5 volts to EEPROM.
If ABL were involved, where's the audio and OSD and remote, etc.?
With no picture and no sound (and no raster [even a dim blank screen] when the screen/G2 is turned up) a |
16-02-2009 | | What a nice and pleasant post. If you leave your email address, I'll send you a free copy of the service manual.
[email protected] |
16-02-2009 | LG Plasma RZ-60 PY 10 | upon switch on various colours flashes etc but no picture.will sometimes take an hour to settle down with picture.later several hours and finally not at all . PS fault? or any ideas?[code][/code]3526 |
16-02-2009 | | Have you checked for bad solder joints etc around the chroma IC? Also, check the signal levels before and after the delay line with a scope. |
16-02-2009 | TV Mitsai TM1402 | I need a scheme of mitsai TM1402. Can anyone help me? You can give me answer to the mail [email protected]
Thank You
Paulo Santos |
16-02-2009 | | My email address is [email protected]
Thanks very much for the copy of the manual.
Daniel |
16-02-2009 | | Done! |
16-02-2009 | | Don't turn the set off - leave the set ON all the time. |
16-02-2009 | grundig tv cuc 220 | i have a problem with my tv . on standby it is ok but when pressing channel from remote control i just hear like a click of a relay the channel number appears for a split of a second and goes to standby again.
can anyone please help
thanks |
16-02-2009 | please help, goodmans gce5007tft wiring | hi,i have this tft screen i have used in the past. recently i have lost the din plug that fits to existing plug. i have phoned goodmans but they are no help. i have removed the rear panel from screen in the hope to trace the wiring. i have 10 pre solde |
16-02-2009 | | I already have the manual and it is no help. What I am looking for is some help on replacing the rear paper path (with wheel), not a sales pitch.
I have since discovered that a small piece of plastic has broken off that must hold the wheel assembly in |
16-02-2009 | | With that kind of attitude and your lack of manners, the only advice I can give you is to spring for a new printer rather than patch together a 25 year old product where parts are most likely non existant anyhow. |
16-02-2009 | | While it definitely sounds like a system control issue, you may want to keep in mind that since a I2C protocol is utilized in this chassis, any device not responding can easily lock up the processor. Short of just scoping the lines, there is no reliable w |