Date | Header | Text |
21-01-2009 | Holden Astra 1996 TR GSI | Hi there
My daughters car, listed above, had a flat battery and now the radio doesnt work. I understand a code is required. The radio is standard with the car. It is a radio with a cassette player and it says eurovox where the tape goes.
I am hop |
21-01-2009 | service manuel for toshiba tv model 29JZ5 | Please I need service manuel for toshiba tv model 29JZ5
[email protected] |
21-01-2009 | Matsui VP 9301 Manual | Hi, I would really appreciate help in finding instruction manual for Matsui video VP 9301 that I can download.
thanks in advance |
21-01-2009 | No Raster with sound, Panasonic TC7-29V50R | Q802 emitter is 84.6volt,base is 84.2 volt . It is not conducting to give me 13volt at Q802 collector.B+ 140volt is present at IC803,+15volt is present at connector P82. As in the circuit diagram Q806 base is controlled by pin 29 of IC1102 when this goe |
21-01-2009 | Many thanks! | Second try here (forgot to log int the first time :(.
Paul, thanks for the info on justmanuals. Too bad I didn't see your site first. Hopefully you'll have a manual for my Viewsonic N4000w.
Too bad that scam, rip-off artists like manualuniverse mak |
21-01-2009 | Need Dump For CD30(Grundig) | Hi all.
Need Dump for cd30-delphi grundig. :D Please. :) |
21-01-2009 | Display Dead / Dimms - JVC RX-5THPBK | Good day. I have a JVC RX-5THPBK amplifier which the display is dead on. I started some time ago with dismantling and trying to find the problem. I have done many tests and measurements which I will include below in the message. I have attached 2 schemeti |
21-01-2009 | | I hope you mean 15 volt is present at P83 (NOT P82), otherwise I'm looking at the wrong schematic.
Could be an excessive load on or defective 5 volt source?
What happens to 13 volts when IC804 is disconnected from foils? Also could try "floating&qu |
21-01-2009 | | may i have a copy too please? |
21-01-2009 | | Are the tubes lit? |
21-01-2009 | Re: Display | "7) I then soldered back those 2 resistors and bridge wire."
Sounds like you're on the right track.
What resistors? What bridge wire/where?
Pin 5 on CN851 comes from where?
partstore.com (under base model RX-5THxx) may have service lit |
22-01-2009 | D940 green light Clicking on middle circuit board. | I have a 6 yr old Hitachi 51UWX20B Rear Projection TV that was working perfectly until the red went out of convergence. Replaced the two STK392-110 IC’s with two STK392-150 IC’s, plus a number of resistors. Initially when I turned power on everything appe |
22-01-2009 | | Cliff,
Although I have not dealt with this "Joe/Mike etc" guy, he is NOT to be trusted whatsoever. Certainly hope you can recover your loss. I purposely flagged [url=http://forum.eserviceinfo.com/viewtopic.php?t=23940&highlight=manualunive |
22-01-2009 | toshiba tp55e50 | My tv has the same problem. There is no sound (besides the initial click when plugged in and the power button is pushed) and no picture. Just a light on the front control panel flashing. If anyone can help with this problem, it would be greatly appreci |
22-01-2009 | Samsung PCL5415R | Picture is showing 3D. Is this a convergance problem? |
22-01-2009 | | Maybe the problem is at transformer primary winding, try the board with another transformer to make sure if the board is ok.
BTW, for me, when i see the picture of your transformer, looks like a vcd player transformer made in china ( just joking ) |