|05-09-2007||LOGIK power module/board????||Hi guys
Names Jordan, 33 from East Anglia in UK. Not really qualified in servicing and repairs but I sort of know enough to repair my own items.
But a fault with my TV has baffled me a little as most repair places seem loathe to touch it.
|05-09-2007||radio wont light up||Hi everyone,, just installed a radio/player in my camper,, a vw, beta with cassette player, it works fine but it dosnt light up the panel when on,, have tried another similar radio an it dont light up either,, strange,,all the wiring block looks ok|
|05-09-2007||[quote:ed8748dd47="jlatenight"]Can I get it for free? :wink:[/quote:ed8748dd47]
Only if you have something to trade.
|05-09-2007||Re: Monitor SGI GDM-5411||[quote:2e62d5470a="moty"]Hello!
I have a problem with my monitor SGI GDM-5411.
It is dead. I need the service manual or some advice to fix it.
Could you help me?
|05-09-2007||iwatsu ss-6122 oscilloscope||Hi,
I bought a Iwatsu ss-6122 oscilloscope for a year and recently when i turned it on, i could not find the trace. I tried to adjust the vertical position knob to the highest position and i could see the trace appearing at the bottom of the screen. A|
|05-09-2007||Hitachi TX34D11VC0CAA monitor and/or Visiondesk 1330 manual||I need info for the monitor TX34D11VC0CAA made by hibachi. I know this particular one came from a Visiondesk 1330 and that is all I know. Any manuals or specs would be greatly appreciated.
|05-09-2007||Apex GB5108||This a easy problem to fix. You say it has a thin line accross the center. Change out IC N301 it is a TDA8351 and it crosses to a NTE7156. Also change R370 it is a 1W/1 Ohm Oxide Metal Resistor
R371 it is a 1W/33 Ohm Oxide Metal Resistor and
R380 it is |
|05-09-2007||service manual for VSX-D498||Anybody got one the these in PDF?|
|05-09-2007||Pioneer VSX - D912 component port issues & refuses to re||I have a pioneer VSX 912 receiver that I am attempting to use to route an AppleTV and hi-def cable to my pioneer SD-533HD5 TV. I also have a DVD player, so thats 3 HD sources that i need to connect to 2 HD inputs on the TV (all component video connections|
|05-09-2007||9p6034c-Philips/Magnavox 60" projection|
|05-09-2007||[quote:d638f0abde="vtech"]Sounds like you need to experiment.... looking at fig 1.1, this unit has a standard composite output. http://www.cisco.com/univercd/cc/td/doc/product/webscale/content/ce500hig/11199ov1.htm#xtocid75143
Depending on the monitor|
|05-09-2007||[quote:751411a959="torbjorn"]So, you have identified the RGB signals, that is a good beginning.
Then, check out which pins in the header that are grounded, that is probably several ones as it is common practice to have a separate ground pin for each of t|
Maybe we can help each other out.
I also have an n3260w with an fsp228-3f01(spi) power supply that has a blown capacitor.
I think the capacitor that is blown on mine is C33 but I'm not sure. (I'm at work right now)
If we do have the exact|
|06-09-2007||In other words, your vertical IC crapped out.|
|06-09-2007||Sounds like a convergence problem. Go into the menu and see if you can align the cross hatches.|
You Can E-Mail firstname.lastname@example.org
Log on http://www.service-manual-owner.com|
|06-09-2007||I'll keep up with this, but like I said the manufacturers don't care. In three days, 3 bad light engines for DLP's, new and defective, one bad signal board Mitt's rear pro jo. Also new and defective. I'd love to say replace Q614 and D112. Factory tech sup|
|06-09-2007||tv interference||About a month ago, we started to get interference on our tv, but just at night. We have Comcast basic cable (not antenna). Interference is on 2 (worst, no sound, pick is just snow) up to 6 (very fuzzy), above 6 it is clear and fine.
|06-09-2007||[quote:4e44e1341f="janders"][quote:4e44e1341f="vtech"]Sounds like you need to experiment.... looking at fig 1.1, this unit has a standard composite output. http://www.cisco.com/univercd/cc/td/doc/product/webscale/content/ce500hig/11199ov1.htm#xtocid75143|
|06-09-2007||Thanks for your informations.
I've started to draw the schematic of the secondary part of the main power supply as I discovered that when I unplug the Vs connector, the plasma start every times. I'm going to go further and maybe I will find the soluti|
|06-09-2007||Check out if you have the same interference when you are receiving by antenna, too. Check if you can find any similar interference on other services (i.e. FM radio, CB radio, cell phones etc).
Try another tv. Try using a battery powered tv and switch of|
|06-09-2007||The ISO connector on car radios has a separate dedicated pin for panel lights. In a car, this is connected to the dashboard lights so that the car radio's panel can be dimmed by the same control.
Usually, aftermarket radios will light up when just the ma|
|06-09-2007||Without any specific knowledge of this specific oscilloscope, i could bet that the problem is in one half of the push-pull vertical deflection output amplifier. For exemple, a shorted output transistor, burnt-off collector resistor or something like that.|