Date | Header | Text |
02-09-2008 | Hitachi convergence blue streak jk07132-1 jt22052 | Hi, I have a Hitachi 53uwx10b with a convergence issue (blue). Im not sure i feel comforrtable trying to solder in new resistors and ics. the board appears to be jk07132-a and i found what appears to be the board both new and rebuilt as part number jt220 |
02-09-2008 | Fujitsu PDS4234 42 Plasma Failure - Blinking RED light | Hi,
I got a Fujitsu PDS4234 42 Plasma and till now it worked fine since 2003.
Now I encountered a few serious problems :
1. After I turn on the TV I can see the picture for a short time then it disapear and the ON/STBY led blinks in RED. and the TV |
02-09-2008 | samsung plano shematic & scvc manual pls:( | hi there, please, i need schematic daig and scv manual fir my samsung plano 21 inch crt tv model CS-21K3S, thank you in advance:) |
02-09-2008 | | This Parts & Service manual can now be purchased for $9.99 and downloaded immediately after payment from http://www.justmanuals.com
[email protected] |
02-09-2008 | Zenith Projection TV | I just picked up (for free) a Zenith Model PVY5265DT. It has sound, but no picture. The screen is entirely blank. There is faint color coming off of each tube (red, green, blue) on the inside of the set. Where do I start?
Thanks |
02-09-2008 | service manual for mitsubishi ws 65613 | The dreaded green blinking light. The tv has'nt powered on for about a week. Have done the, un-plug, reset, and various combos to no avail. Figure it is the caps on the DM module that need to be replaced but I need the service manuel. Thanks |
02-09-2008 | | Why do you want to erase the error buffer? Notes there does not affekt any funktion of the set. If you necessary must... there is two way´s.
Get a´"DST" service remote (not longer avaible) Or short the service jumper marked SAM on the |
02-09-2008 | Schematic for a Hitachi karaoke player model #AK-G77 | Schematic for Hitachi karaoke player Model # AK-G77. Print out would be fine. THANK YOU. |
02-09-2008 | | Service manuals are worthless!!! Check C9B01, C9B02, C9B10, and C9B11 (1000 uFD 16V) on the DM PCB. Those are the ones that go bad. The tops will be 'mushroomed' up. |
02-09-2008 | | First check R5102 on all crt boards 120k ohm. |
02-09-2008 | | [quote:d7affc9f03]It's the precision soldering that i am not comfortable with.[/quote:d7affc9f03]
I'm legally blind and I manage! :roll: |
02-09-2008 | | Recheck the pico fuses. STK393-110 is a 6 channel amp. So yes, there would only be one in this set. Usually when you unsolder the IC half of the pins fall out of the IC. :roll: |
02-09-2008 | blaupunkt kiel:" I know the code - problem to fill it i | Hi,
after my little son pressed some keys of the RC car hifi after the winter pause (batts were disconnected) blaupunkt kiel (don't know the number, but I can get it if nessecary) I can not fill in the code.
Means I know the Code but there does not hap |
02-09-2008 | American electronics in Germany | Hello,
I'm an American who has just moved to Germany. I've got a bunch of American electronic equipment. It seems like the only practical thing to do is run the equipment into an American surge protector, the surge protector into a convertor/adaptor, |
02-09-2008 | | Post your question in:
Decode, Unlock, Service and hotel mode entry HowTo |
02-09-2008 | | i found another one rebuilt part that showed the part number j22032r DUD - I wasn't sure what the dud stood for, any ideas? |
02-09-2008 | | Check your PM. |
02-09-2008 | Philips FWC 52, Need service manual | Can someone help me with a service manual. Thanks |
02-09-2008 | Schematic for power supply AV-76 | I need a schematic for the internal power supply on a Roland VA-76. The power supply is a Kartis SWM 40 Rev B.
Any help would be appreciated.
Chuck |
03-09-2008 | | Today I check flat cable and everything is ok with him.
Any other solutions? |
03-09-2008 | H.output transistor | If your transistor is indeed a C5801, you can sub the same with an NTE
2662.
Good Luck |
03-09-2008 | | I think you just made my Christmas Card List. :) |
03-09-2008 | AV Receiver Won't Respond to Remote Control | I have a similar problem. My Kenwood AV receiver no longer responds to its remote control, which still emits IR signals (based on viewing the RC through a digital camera). Is there a part I can replace in the receiver? How do I locate the defective par |
03-09-2008 | Re: American electronics in Germany | [quote:25f6c12a04="joshc"]Hello,
I'm an American who has just moved to Germany. I've got a bunch of American electronic equipment. It seems like the only practical thing to do is run the equipment into an American surge protector, the surge protector |
03-09-2008 | Re: Schematic for power supply AV-76 | [quote:75b4de0785="Cnacc"]I need a schematic for the internal power supply on a Roland VA-76. The power supply is a Kartis SWM 40 Rev B.
Any help would be appreciated.
Chuck[/quote:75b4de0785]
Very unlikely to get a response here. May want to contac |
03-09-2008 | | well, lo and behold I managed to find amatching complonet on an old SB16 I had lying about.... woo hoo... now to figure out whats wriong with the IDE controller.... |
03-09-2008 | | IR sensor. |
03-09-2008 | | 60 hertz vs 50 hertz. Pal vs NTSC. |
03-09-2008 | sony KP-41DS1U | Hi, I have a sony KP-41DS1U. it is 8 years old. it suddenly switched off and if I push the power on button, it turns on for a second, then off. the red light comes on but only for a second. any ideas please. Rob |
03-09-2008 | | Something you definitely should've checked out beforehand.
[email protected] |
03-09-2008 | | The major problem is the mains voltage, 230 V in Europe as related to 110-120 V in the US. This problem is most easily solved by using an 230/115 V transformer, but make sure that it has a large enough power rating. You should use a full transformer rathe |