|22-01-2007||phillips sucks||Mine turns itself off all by itself. :x It has now decided to really tick me off today. I turn it on, w/in seconds it turns itself off and the power button will blink two times then stop for sec and do it again :x . I am starting to hate this thing.
|22-01-2007||Service Manual Fujitsu-Siemens Amilo M1425 or equivalent||I need Service Manual of the laptop Fujitsu-Siemens Amylo A1667AG or A1667EX
Necesito manual de servicio del portatil Fujitsu Siemens Amilo A1667AG o A1667EX
|23-01-2007||Im in need of service/repair manual for phillips 55pp970104||In need of service/repair manual for phillips 55pp970104
It looks like the red went out in my tv and I need to know how to replace the red bulb.|
|23-01-2007||Service Manual Fujitsu-Siemens Amilo M1425||I need Service Manual of the laptop Fujitsu-Siemens AmIlo M1425
Necesito manual de servicio del portatil Fujitsu Siemens Amilo M1425
|23-01-2007||RCA CTC197AH F27680GY Headache||Hi Guys,.Me again,This set had good pic after i did some convergence adjustements,but now the set runs great for 45 minutes, and sudden gets a Horizontal 5 inch pic top to butom and fades away with no raster just blunk screen, but sound is good,at first i|
|23-01-2007||I've got the Parts & Service manual for the VSX-808RDS Receiver, is your manual for the 508 parts and service or just schematics?
You can contact me email at firstname.lastname@example.org|
|23-01-2007||Isolate it first. Make sure it is one of the tda's. Pull the 4 pin wire and see if the set stays up.|
|23-01-2007||Most of these complaints are the SSB. Int sound, turns off, won't turn on ect.|
|23-01-2007||Sony trv-118 blown speaker?||my friend gave me a ccd trv118 camera to fix the internal speaker, there was no sound.
i took it apart and determined that the speaker is blown
its very small 16mm ( 1/2 inch ) in diamater with a wire 5 cm long
the speaker cone is plastic
|23-01-2007||I uploaded it for you
|23-01-2007||what do you need tahat file for, be more specific|
|23-01-2007||pioneer receiver overload||Anyone know what could cause an overload fault in a pioneer VSX-D509S? Doesn't matter which input i have it on, the overload indicator is always lit after the speaker relay clicks. No sound comes out obviously.
Here's what happened. House was struck by|
|23-01-2007||Replace your convergence ic's, STK392-560's I believe. Look to confirm.|
|23-01-2007||[quote:c6ead96b7d="minnie"]He probably didn't get a good seal on the blue crt when he changed the fluid. Look around the blue tube for fluid. If you see it which sounds like you will, yes it's his fault. Then ask why he didn't change the fluid in the gree|
|23-01-2007||The set won't even turn on! I plug it in and all I hear is the ticking sound. Where is this CRT board? Aren't there three of them? Does anyone have a service manual that I can download? BTW, I mean no disrespect to TV repairmen, but this day and age they |
|23-01-2007||digital update||I've tried feeding a DD signal from a dvd player into the digital board, and i get no DD on the stereo. I'm guessing the digital input board is also roasted... :(|
|23-01-2007||i need a vga input cable diagram for this model. thanks!|
|23-01-2007||Hey minnie, I did what you said. I eventually found the CRT boards (the color board was written on the chip its self). I tried every combination immaginable. The television still doesn't turn on! How screwed am I or what... I'm not going to give up on it |
|23-01-2007||even more of an update.
I've toyed with it all night trying to see what happens when. Here's what i know. The thing works "fine" in stereo mode. IE no DSP settings, no loudness, no tone control. Just flat. If i turn on loudness, the overload |
|23-01-2007||Canon GP335 photocopier feeder problem with DADF-A1 feeder||Hello,
I have just been given a second hand photocopier. Its a Canon GP335. It has not been used for about 6 months, and was very dusty. I have given it a good clean and the basic copier seems to work very well.
However the sheet feeder (DADF-A1) is|
|23-01-2007||i have same problem too||AKIRA CT-21TF9CP can't find channel , do u know ?
Please help what the problem ?
|23-01-2007||Pioneer VSX - 808 RDS||Thank you very much Hotwaterwizard!!
|23-01-2007||HP71 Model D8901A Monitor/at cross roads||hello guys!
please help me!
i have HP71 monitor 17" color model D8901A chasis CMC4217.
it was all running ok. suddenly there was a very bright thin vertical white line in the monitor.
i watched closely and found as if the picture was sq|
|23-01-2007||monitor Benq V772 Led green on||G.morning,
my monitor Benq V772 do not work, only a green led stay on,
when I disconnect the VGA cable, the green led stay on, there is no change.
anyone can help me.|
|23-01-2007||Likewise! (it's a W282NS) Though more detail if it helps:
Started a few days ago, the picture would briefly blank out - though not a 'flat' black screen - it was in the same way as if the set was being put into standby - for a fraction of a second, an|
|23-01-2007||SONY ST-EX10 Tuner||I'm looking for a free service manual / schematics of a SONY ST-EX10 Tuner. Can someone upload this please?? Much appreciated.
|23-01-2007||When you say it won't switch on. Do you have a red light or anything lit up on the front?|
|23-01-2007||Toshiba 50VJ23P 50" Rear Proj Screen Prob. Single line||Hi. Does anyone have an idea as to why I have a black screen with a single coloured horisontal line across the middle.
I have perfect sound.
I'm fairly good with electronics and have tried to take a look myself.
It maybe the IC LA7833 (vertical d|
|23-01-2007||Yes, its actually a green light (you guys are techs, so I thought I would be as specific as possible). Anyhow, when I run the above tests, its seems that the system will continuously restart its self when the green crt board is not hooked up. However, whe|
|23-01-2007||Service manual of TV SHARP 21M-H50||I need the service manual of TV SHARP model 21M-H50, can somebody help me?.......This TV set have not video in......how can I do it?.....Thanks|
|23-01-2007||How can I see the *.bin files ???||use hex editor|
|23-01-2007||more likely to be a short circuit line output transistor caused by dry joints in the line output stage, this will cause the power supply to trip due to overload, replace the line output transistor and resolder all hv caps in line stage.|
|23-01-2007||Thanks gary. I might still take the lid off just to make sure it isn't stuffed full of dust but it sounds like it would be wise for me to get someone else to do the actual fixing - parts, equipment, safety(!)...
(but your fix duly noted, will post back o|
|23-01-2007||Input for video in TV SHARP||How can I inject video signal to an TV model [b:74c8be38e1]SHARP 21-H50[/b:74c8be38e1].....this TV set have not the plugs for video and audio and I want place it but don´t know where connect it in the board.....how can I do it?......Can somebody help|
|23-01-2007||Any one ply help how i can repair a dvd player in step||[b:e03b06bd27]Hello all of my seniour member ,
PLZ tell me that the hoe i can repair the any ordanary dvd player repair ??[/b:e03b06bd27]|
|23-01-2007||[b:6651d10a9a]Check OR change u r [u:6651d10a9a]CD LOADER[/u:6651d10a9a]
And post result[/b:6651d10a9a]|
|23-01-2007||RCA 44" Rear Projection DLP screen Issue- please help||Long story short, my new DLP tv has a faded gray circle that shows up during moments when the screen is black during viewing. Is this a serious issue?
Sorry if this is the wrong forum. This information has seemed tough to come by.
Thanks in advance!|
|23-01-2007||Post here all ONIDA Television Sceamatic||[b:8a3cbcea58]hello all of u
PLZ post here only ONIDA sceamatic
Tahnkx in advace !![/b:8a3cbcea58]|
|23-01-2007||It could be an optical illusion. Play a dvd where you can see the spot and pause it. Cover the screen completely with you under it and see if it's not out side light refracting thru the screens. If it's still there I'd say dust in your light engine.|
|23-01-2007||dual cd player||thanks for the reply i have checked the loader and when the cd loader didnt come out i tapped the top by the magnet, and this made the loader come out ????? so i dont think this is an electrical fault any more ideas could i use some kind of lubricant or d|