|17-09-2011||Where can be downloaded the Instruction or Service manual for Racal Dana 5001 ?
|17-09-2011||When turn on the 5001 POWER show Error 4
How to calibrate this DVM ?|
|17-09-2011||Try clicking on the words "Get Manual."|
|18-09-2011||Nintendo schematic||I am trying to fix a monitor problem on a Nintendo early 1980's donkey kong cocktail table. The model is tkg3-tbl. I have the original manual and wiring diagrams. I need a schematic of the monitor and the video boards to find out what components are the c|
|18-09-2011||Welcome in this post torbjorn, thank you very much for your precise and accurate information, but as I mentioned before I haven't a scope.
I know the scope is extremely indispensable when repairing tv, especially in this case.
Several months ago, I sa|
|18-09-2011||me 2||i have the same problem with mine! did you find a way to make it work? if so let me know firstname.lastname@example.org|
|18-09-2011||me 22||i have found how to fix it. you need to unplug the unit for a min or so, then hold the skip track forward and ECO buttons while plugging the unit back in.
it will give system info on the screen, then press the skip track back button and it will reset all|
|18-09-2011||KDS60A2000||Well minnie that took care of it. I swapped out the lamp, they gave me a new one, they tested it and said it was not firing correctly. Anyway all is well with this tv. I will give it to my mother in law so I can watch the football games this winter whe|
|18-09-2011||Mitsubishi 42" tabletop tv||Have a guy locally wanting 40.00 for a 42" mitsubishi table top rear projection tv. He said it is only 6 yrs old so I was thinking a dlp maybe. did they stop selling the rear projection tvs then? He said the picture is reddish in color, and has a 3|
|18-09-2011||Sounds like a thermal issue, perhaps the capacitor(s) in the vertical circuit? Using a can of freeze spray can be handy in pinpointing the culprit.|
|18-09-2011||Mitsubishi 42"||The model number is a WT-42315. Thanks apprears to be a non dlp tv.|
|18-09-2011||I didn't see any link or clickable button or even the words for that matter, for "get manual"when going to that link. I hate when it looks like Ii am clueless at this level of enquiry! is there a way you can send me a pm with the link or the m|
Thanks for the link. It seems that the question I really need to ask is whether each pixel is it's own compartment with respect to gas leakage. I have a set with a small star crack about 3" or so around...if each compartment is separate |
|19-09-2011||Mitsubishi 43" tabeltop||well I bought the TV pulled the main board flipped it over and found 1 bad solder joint on one of the convergence chips, really had no solder on it at all. the solder pad looks good, I guess I will try to re solder it and see what happens.|
|19-09-2011||Samsung MAX 980||The volume control if turned clockwise or anticlockwise only increases the volume. The remote control works fine.
Can anyone tell me how do I remove the volume control knob to check what is the fault ?|
|19-09-2011||ti86 horizontal lines in the display||mine did it and here is the fix,
the problem was caused by the foil shielding inside the calculator was shorting the traces and chip pins.
1) open the case by removing the bottom screws and the screw near the backup battery and then remove the batter|
|19-09-2011||service manual canon fax l220||dear sir
i need the canon laser fax L220|
|19-09-2011||Samsung MAX 980||Sorry my question is not spot one.
I find the knob just pulls off. However the problem is getting the board out
without dismantling just about everything inside the "box".|