Date | Header | Text |
07-10-2006 | EEPROM bin files | Hi,
Is there a website that has eeprom bin files for download. I am about to buy the eeprom equipment to program the eeprom but i need the bin for a Goodmans GTV69RF2.
Appreciate any help/file/pointers/advice please.
Thanks |
07-10-2006 | Sony KV32FS100 | I need a copy (electronic or hard) for Sony tv model KV-32FS100 service manual. The television blinks 2 red light codes, but does not power up.
Took it to a repair shop that replaced the power supply board, but is clueless what to repair next. I really |
07-10-2006 | 1997 Magnavox TV dead | TV was on all night, and in the morning TV was dark with no pic or sound. Turned off for a few minutes and TV came back on.
A few hours later, TV was "dead" again. Noticed power light was still on. When I tried to start again, I heard the &qu |
07-10-2006 | HOW TO KNOW THE RESISTOR IS SHORT | HOW TO KNOW THE RESISTOR IS SHORT
BY ANALOG METER |
07-10-2006 | cnr 10d471k VARISTOR how to know is short or not by | cnr 10d471k VARISTOR how to know is short or not by
analog meter |
07-10-2006 | | Resistor can not short? Perhaps you meant to ask how to check for an open resistor?---easy ...your analog meter will either not read anything or may read much higher than what the resistor value suppose to be. |
07-10-2006 | | Gary I am only getting .03v across pins 1 & 7 of the ic501 |
07-10-2006 | conector vga 15 problem with colours | I have a monitor LG StudioWorks 710S and I have to solde the vga conector, the problem is the colours.
the cable has the next colours:
four fat cables: pink, blue and green ( I suppose RGB cables) and transparent
five thinner cables: orange, yell |
07-10-2006 | canon MP390 | Help me
Canon MP390 error ##345 |
07-10-2006 | NEC Plasmasync 50 MP1 | When turning the set on I get the usual click, followed by popping sounds. No display (altghough the fans work) then the unit will shut down after 10 or so seconds and the green/red light will flash as the system enters self protect mode.
I’m guessing |
07-10-2006 | Kenwood CD player hook-up | Hi there ,
If I hook-up my Kenwood KDC-C601 CD changer to my car radio Kenwood KRC759R it does'nt work, can anybody tell me what I am doing wrong or is the combination of the radio/cd changer not o.k..
Am I using the right cable? (13 pin)
I hope anybo |
07-10-2006 | | I tried to post last night but it would not take it. this is what I wrote, I hope it explains:-
The B+ is the output from the chopper transformer which feeds the HOT and eventually the line transformer. If you are lucky there may be a B+ marking on the c |
07-10-2006 | | These type of problems could be a dried up capacitor or a failing connection or even something else. You could spend hours checking all of the solderjoints with a microscope or testing all of the electrolytics with an ESR meter. :)
The voltage for the s |
07-10-2006 | canon clc 550 fuser oil leakage, also service manual request | Hi everyone, I'm new here!
I've just been given a Canon colour laser copier 550. Unfortunately, during transit the fuser oil cartridge became unseated and leaked everywhere - all over at least one circuit board and god knows where else!
Does anyone |
08-10-2006 | BLAUPUNKT TRIER CC31 | need manual for blaupunk trier CC31
thanks. |
08-10-2006 | Schematis ViewSonic VE170M | Does anybody have the schematics of the Viewsonic VE170M LCD Monitor? Please send it to [email protected]
Thanks! |
08-10-2006 | PSU | Hi
Did you ever find any schematic for this PSU. Cos I blew one I think it is R34 that needs relacing, that is the only check i noticed visually
could you email any details to [email protected]
kind regards
jon |
08-10-2006 | chema | http://www.eserviceinfo.com/download.php?fileid=24855 |
08-10-2006 | power amplifier | Hello does anyone know where can i find service manual for a PEAVEY power amp or for others power amp . |
08-10-2006 | | I have done all these DC tests and results are good yet when I connect the HOT collector and switch on the P.S. trans blows. The only thing that can draw full current with the horiz pulses present is the LOPT and Horiz yoke that is why I am curious to rep |
08-10-2006 | Re: Conrac 4142 x-sight plamsa (fujitzu) resistor values nee | [quote:82335e477e="guyalo"][quote:82335e477e="skeith"]I am having trouble finding a schematic diagram for this unit.
These resistors were burnt beyond reading values from the old ones.
R275
R274
R21
These are located beside T1 and T5 on the Pow |
08-10-2006 | Broken flatcable sony cdx m700 14 pins (carradio) | Where can i get that kind of cable ????
Please email me at [email protected]
many thank |