|19-01-2009||All u say it's happening. the 2 pin output from the button is doing exactly what u say. does that mean that the IC is probably damaged?|
|19-01-2009||parts||if you decide to scrap this TV, i REALLY need the power supply.
please let me know firstname.lastname@example.org|
|19-01-2009||LCT32HA36||looking for power supply module for LCT32HA36
i'm pretty sure it can come from the ILO or the AKAI tv with the same model #
if anybody gives up and decides to scrap thiers, please drop me a line
|19-01-2009||i need a schematic for Pioneer KEH-P660r||I need the outline for the car charger cd model Pioneer KEH-P660R.
I found this part in the textbooks, but I do not Part 2 zip.
I am very grateful
greetings to all|
|19-01-2009||Have you make sure those two signal connect to IC? if you have very sure, it could be the IC problem, to make sure the IC in good condition or bad, i suggest you to find data sheet for the IC and check all of the signal that come and out from IC, maybe th|
|19-01-2009||Yes the drum is free to turn, then when i push Play i can feel with my finger that the drum became hard to turn for about 1-2 seconds. It's like the magnetic field doesn't rotate. As a non expert in VCR repair i am asking if it's possible to test the hall|
|19-01-2009||No power!||I can't get my Mitsubishi VS-7083 to work. I'm a church youth director, and this TV was donated in working condition. It hasn't been used for maybe 3 years and doesn't work. No big surprise.
The TV is plugged in and doesn't turn on. The outlet wo|
|19-01-2009||Check fuses and regulator.|
|19-01-2009||already achieved||already achieved
Sorry for the inconvenience
now I need the diagram cd loader cdx-ps24s
|19-01-2009||Need Luxman A-007 Service Manual or Schematic||Badly needed, Luxman A-007 Service Manual or Schematic.
|19-01-2009||ok thanks, i guess the previous owner tried to plug this in and get it going a few times because it feels like the wax around the copper has melted and thats whats causing it to short. thats why this gets very hot in in 20 sec...
I have a 15.2 volt tra|
|19-01-2009||Remember your AC 12/13 volt winding is center-tapped. Usually so unit can get equal but opposite polarities of voltage (Plus & Minus 18 volts, for example).
Can't tell from your photo how D3, D4, D7 & D8 are connected, but suspect are either a 4-|
|19-01-2009||here is two pics which should show that the rest of the board is just fine
|19-01-2009||Is it just my eyes, or shadows or photo? Over by three-ganged pot. R23 and next one to right "look" discolored?|
|19-01-2009||Nope its a shodow, there is no dis-colouring on the board except for around the caps to the left of the "char-coaled" part|
|19-01-2009||Do you have meter to measure across filter caps? (The largest one for the single supply and the two 3300ufd for the +/- supplies).|
|20-01-2009||ivtec||[quote:69a817eef2="minnie"]New wireless router or different anti-virus.[/quote:69a817eef2]
Thanks, i solved by going in the firewall and click advanced settings and local area connection put a mark on DHCP 67 and voila i'm all good to go|
|20-01-2009||[quote:91b502503a="pmc"]Yes the drum is free to turn, then when i push Play i can feel with my finger that the drum became hard to turn for about 1-2 seconds. It's like the magnetic field doesn't rotate. As a non expert in VCR repair i am asking if it's p|