Date | Header | Text |
15-12-2007 | HIKONA TC-1400 please please help | I HAVE FRAME COLAPSE JUST A LINE ACROSS THE SCREEN TRIED DRY JOINTS EXC HELP WOULD BE VERY WELCOME PLEASE HELP IF YOU CAN |
15-12-2007 | seeking 4 data about "TDA9381ps/n3/... | hello everybody!
I looked for data about "tda9381ps but i find nothing.i searched in my usual websit"alldatasheet.com".but in vain.Anu one to help me about this .thanks in advance. |
15-12-2007 | | http://www.datasheetarchive.com/TDA9381-datasheet.html |
15-12-2007 | tv BEKO shassi 20.2 | Can someone plz help me with the service manual for tv BEKO shassi 20.2 |
15-12-2007 | toshiba 46hm95 turns off. | I turn the power on then I get several green blinks and a solid red light and tv turns off.I try this once or twice sometimes the tv turns on sometimes it doesn't.If that doesn't work after the third attempted.I then unplug it, wait 30 seconds power it up |
15-12-2007 | | There are screws under the keyboard which must be removed before you can separate the two main parts of the casing.
After removing one screw on each hinge cover, you should then be able to prise off the plastic bezel above the keyboard. This is the one w |
15-12-2007 | | I just stripped the Easynote Argo C (what a cheap and nasty thing it is!)
Forgot to mention in my previous post - there are also screws under the plastic bezel I spoke of. There is one hiding under the screen (vga) cable. You'll need to disconnect it g |
15-12-2007 | LG DU-42PX12XD screen dead | Last night the screen of my tv randomly turned off. the power stayed on, but the monitor and sound just clicked off randomly so the light on the bottom is still green, but its like the tv isn't on. im not very experienced with problems like these, and any |
15-12-2007 | | www.tacp.com
Customer support
Recalls and updates
Information for Owners of 2005 DLP® Televisions
Enter model and serial and see if you qualify for the 2 year lamp coverage.
If not, you'll have to pay. Lamps are rated for 4/6000 hours. |
15-12-2007 | | If the power light stays on I'd suspect the digital main board. |
15-12-2007 | | Put new IC's in again and check F850 and F851 5 amp pico fuses, you may have toasted them if you solder blobbed. |
16-12-2007 | Sony TV KV-27510 | TV has worked fine all these years and now picture turns light blue, then you hit the side of the cabinet and the picture will come back on very sharp but only last 5-10 minutes then screen goes light blue. Any suggestions? |
16-12-2007 | rgb | yes,try to adjust the rgb trimmers on the crt board |
16-12-2007 | Front A/V jacks | I have a Samsung tv and I am having trouble with the front A/V jacks. We had the dvd player plugged into the rear jacks and used the front jacks for the game console. Unfortunately we constantly plugged and unplugged the game console, which seems to have |
16-12-2007 | RCA Projection TV Convergence - P46150WK | Hello and Happy Holidays. Hoping someone can assist me with a repair on a 1991 RCA 46" projection television. I am the original owner, can solder, read schematics, but have no TV repair experience or service manuals.
The color convergence fails |
16-12-2007 | | try resoldering the connections on the rca jacks.probably solder connections cracked. |
16-12-2007 | | remove back and check for broken solder connections on crt pcb.the board attached to the rear of picture tube. |
16-12-2007 | | sounds like either the ysus or zsus pcb failed.i think this model might have a kit to replace ysus,zsus and display controller pcb.you can check for blown fuses on ysus and zsus. |
16-12-2007 | no data about tda9381 in datasheetarchieve | hello everybody ,that link doesn't work .the page is empty... :( .i mean datasheetarchieve.thanks for your help .i'm still in crisis .. :( |
16-12-2007 | Searchin gorenje washing machine service manual | I'm really need to find Gorenje WA74163 washing machine complete service manual in order to repair it for one of my customer
thanks in advance for your answers
Cordialy :wink: |
16-12-2007 | Need help identifying type of SMD component | On ATI capture card, component is labeled on board with B, such as B27, B28, B29, 2 leads, looks like resistor and always has cap beside it.
Never saw a B beside a component like this..what the heck is it? Thanks |
16-12-2007 | Finlux 9670 with waves in picture | The problem is a Finlux 9670 (very old thing).
The picture is bulging a little according to the the signal. Vertical lines in the picture gets a wave-like shape.
It looks a bit like the 50 Hz ripple that you might get if the main supply capacitor |
16-12-2007 | | I have had problems with the front control panel on similar tv's. Try to unplug the connector to the control panel, and see if it helps.
Just a shot in the dark, but worth a try. |
16-12-2007 | | For a start, you can try to replace the main capacitor. It's the largest capacitor, usually ca 150-470 uF / 400-450 V. |
16-12-2007 | | Replace all the small electrolytic capacitors, specially on the primary side of the transformer. Big chance one of them is faulty, preventing the psu from starting up. I have replaced a shitload of such, with success almost every time. |
16-12-2007 | | Get "Plastik 70" spray, or similar, and "paint" all coils with it. Your problem is resonance. |
16-12-2007 | | Remove the batteries from the remote, to exclude the possibility of stucj buttons on the remote.
If that doesn't help: Check front panel controls on the TV.
If that doesn't help either: Check voltages on the processor input pins where the signals fr |
16-12-2007 | | Try to jump-wire the output from one of the known working RGB-outputs to the pin of the canon on the CRT that doesn't work, to see if it's the output-stage or the CRT that's faulty. |
16-12-2007 | | This tv is well known for bad solder joints. Re-solder the line output and power supply area first, no matter what you do next. |
16-12-2007 | | Your CRT is probably about to get worn out. Adjusting Ug2 will only work for a certain amount of time. In the end you'll have to scrap the tv. |
16-12-2007 | | thanks a bunch! |
16-12-2007 | Looking for S.Manual for Video Beamer InFocus LP540/LP640 | Hi Guy´s,
i´m looking for a Service Manual for a Video Beamer.
Manufacturer: InFocus
Model: LP540/LP640
Thank´s in advance
Bertl |
16-12-2007 | | Nobody to help me? |
16-12-2007 | | [quote:db448873c2="minnie"]Put new IC's in again and check F850 and F851 5 amp pico fuses, you may have toasted them if you solder blobbed.[/quote:db448873c2]
I checked F850 and F851, they both look good. I'll put the IC's back in and hopefully that w |
16-12-2007 | | You have to check them with a meter, looking won't tell you everything. They may look ok but their open. |
17-12-2007 | | Actually have not been able to get to the switch - yet.
It is BURIED inside and inbetween about a ton of plastic.
:(
I have the deck out, but the only way to get to this switch, is to remove the whole drawer assembly, which I am reluctant to do, as i |