Date | Header | Text |
03-07-2015 | | ah i think it has a memory of the last power state, so if i shut it off with the power button, then it doesn't click the next time i plug it in. in this case, the fuse doesn't get blown until i press the power button.... |
03-07-2015 | | Item 62 has two pins on one side (Primary) and seven on the other (secondary). Unsolder and let float in mid air either of the primary wires.
I'd like you to leave unit in the 'Off' position, and let me know if for your last if it had a good fuse install |
03-07-2015 | | I take it you have No or sporadic EDIT feature too? |
03-07-2015 | | yeah sorry... no edit button over here, must not be enabled on this forum.
okay pin 1 on the primary side floating, good fuse installed and plugged into mains. unit is "off" and the fuse is still intact. |
03-07-2015 | | If fuse not blowing with primary disconnected, reconnect and unsolder all 7 connections on the secondary. If memory serves, there aren't any plug/sockets on the multi-wire connections. The little circuit board (43) with the larger solder pads should have |
03-07-2015 | | ok so with the board (43) floating, i measured from each pad on that board to ground. some of the measurements were a little jumpy, i probably didn't clear off the solder very well, but eventually all the pins except 4 were reading outside my meters rang |
03-07-2015 | | actually when i turn down my meter to 200, pin 4 is actually measuring about 13 ohms... not sure if that is significant or not.... |
03-07-2015 | | You missed a few answers to questions I previously asked?
1) With good fuse and Primary wire floating, did plugging in and turning on result in fuse blowing?
2) With good fuse and secondary board (43) completely removed from transformer, did plugging i |
03-07-2015 | | So much for my auto-ranging meter presumption.
You're looking for any unexplained reading of less than a few hundred ohms. |
03-07-2015 | | well #1 i can't test now because i reconnected the primary and have the secondary completely disconnected.
#2 no the fuse does not blow
#3 it was a few days ago while the unit was on and playing the radio. when the music stopped and we noticed the |
03-07-2015 | | So much for my auto-ranging meter presumption.
You're looking for any unexplained reading of less than a few hundred ohms. |
03-07-2015 | | oh well if you can't explain it then i surely can't! do you suggest we toss it and buy the one on ebay for $40? :) |
03-07-2015 | | OOps - No delete feature either.
No need to do #1 if is OK on #2.
IF only a drop or two, a day or three with no airflow or warm sun beating down on it should be sufficient.
IF more, you may want to let it evaporate further (or put in the breeze of |
03-07-2015 | | You can check (Q1 thru Q4) between each output transistor leg and ground for shorts.
You could put your meter on 'Diode Test' and check the bridge rectifier, if its NOT mounted flush to the board. |
03-07-2015 | Re: samsung 40f6400 tv card bn44-00662A scheme -request | I also have samsung UA40F6400 with same problem. If you got any answer please tell me. My email I'd is [email protected] & my mob no.9545631199. Please please help me |
04-07-2015 | | should i measure those with the board (43) still floating, or should i solder that back on at this point? |
04-07-2015 | | I'd leave it off until bridge is tested: [url]http://www.ehow.com/how_7918714_test-bridge-rectifier.html[/url] |
05-07-2015 | Re: how to unlock onida tv volume lock | [quote="[email protected]"]How to unlock onida tv volume lock
Modal co29 sl 400 bl
PLEASE OPEN SERVICE MODE USE WITH YOUR ORIGINAL REMOTE CONTROL (VSM AND OSD(DISPLAY) SAME TIME ON RC) WRITE DOWN ALL DATA FROM YOUR RECORD. CHANGE NEW EE |
05-07-2015 | heater fan | My Opel corsa 1.4 utility heater fan does not run. I dont know whether it is a relay. I 've checked all fuses, none is blown out. Can you help |
06-07-2015 | Toshiba 40S51U | Need the service manual for the 40S51U LED TV or at least the for the power supply board. |
06-07-2015 | | Have you seen [url]http://www.justanswer.com/tv-repair/908iz-toshiba-40s51u-no-power-standby-lights.html#re.v/184/[/url] ? He goes through how to determine if PS is food or bad. |
06-07-2015 | | Dumb - No Edit button.
"good" |
06-07-2015 | My 650VA APC UPS is malfunctioned,no power on battery points | Some pls help me. My 650VA APC UPS while energized does not have power on the 3 battery source point of the ups but only on the one and only surge point on the device and when d-energized, the reverse is the case, power comes on the batery source point an |
08-07-2015 | | HI
I have recently bought Astra with Delco cdr500 radio.
changed battery and don't have code for radio.
Any help would be greatly appreciated.
No 09136107
Type CDR500(E)
GM150010056620 |
08-07-2015 | | [quote="rv_asenov"]HI
I have recently bought Astra with Delco cdr500 radio.
changed battery and don't have code for radio.
Any help would be greatly appreciated.
DELCO CDR500(e)
NO.09136107
GM1500Y9504489 |
08-07-2015 | | [quote="rv_asenov"][quote:a0dd3f76f6="rv_asenov"]HI
I have recently bought Astra with Delco cdr500 radio.
changed battery and don't have code for radio.
Any help would be greatly appreciated.
DELCO CDR500(e)
NO.09136107
GM1500Y |
08-07-2015 | | [quote:b3b0bba5da="rv_asenov"]HI
I have recently bought Astra with Delco cdr500 radio.
changed battery and don't have code for radio.
Any help would be greatly appreciated.
No 09136107
Type CDR500(E)
GM150010056620[/quote:b3b0bba5da]
|
08-07-2015 | | [quote="REZON"][quote:a8806cee7c="rv_asenov"][quote:a8806cee7c="rv_asenov"]HI
I have recently bought Astra with Delco cdr500 radio.
changed battery and don't have code for radio.
Any help would be greatly appreciated.
DELCO CDR500(e) |
08-07-2015 | Suzuki Ignis. Radio code, blaupunkt/Bosch. | Hi!
Can somebody help me, I have changed the battery in my car and now the radio wants a code =(
If anyone could help me i be happy!
Inscription on the plate:
BOSCH
3 6809212 7643063510 7
39101-86G10
ID: 39101-86G1
Made in Malaysia
On t |
09-07-2015 | | ok on step #3 it says to test the AC inputs. the first measurements reads 1370 and after swapping the leads the read-out is 1367
in step #4, with the positive lead on an AC input and the negative lead on the positive output, the reading is 550 and the |
09-07-2015 | | Here's what I was taught:
'a' and 'b' can be done with the Bridge diode IN or OUT of the circuit, IF it tests good in circuit, it IS good. If it tests strangely in circuit, it's best to remove and retest out of circuit.
a) Put the black meter test lea |
09-07-2015 | | ok i removed it and re-tested it out of circuit...
[quote:f5928f4ab4="jts1957"]
You should get two over-range readings with the leads connected one way and two numeric readings with the leads connected the other way for BOTH 'a' [u:f5928f4ab4][b:f5928f4 |
09-07-2015 | | BTW here is what the bottom of the circuit board looks like
[URL=http://www.image-share.com/ijpg-3000-14.html][img:b1260222f6]http://www.image-share.com/upload/3000/14m.jpg[/img:b1260222f6][/URL]
seems there is a lot of residue or burn marks or somethin |