Date | Header | Text |
30-01-2009 | panasonic SA-PM45 sterio | Can only get sound from headphonr socket
Can anybody help.[/quote] |
30-01-2009 | | anyone know where i can get a free schematic of the board? |
30-01-2009 | Carver receiver hr-895 one channel noise | I bought this receiver very inexpensively because the right channel has an intermittent scratching sound with occasional louder pops. Seems to get somewhat worse as the unit warms up then it stabilizes to it's usual noise It is unaffected by the use of t |
30-01-2009 | | Even if the service manual was available, it wouldn't include the schematic.
No laptop manuals include schematics, at least none that I've seen.
HtH
[email protected] |
30-01-2009 | | i have tested areas with a multimeter and it seems to be getting power everywhere, 3.3v, 5v and 18v at various places on the board, capacitors all look fine, so my guess is bad power ic, voltage regulator or sm fuse somewhere :lol: i have no idea |
30-01-2009 | | [quote=" i have no idea[/quote]
yes, thats obvious |
30-01-2009 | renault megane scenic | Hello, may someone help me to get the radio code for my Renault Megane?
radiosat 6010
Philips, model nr: 22DC461/62L
7700 433 072
9022 214 61624
RN 481FW411118
e-meil [email protected]
Thanks! |
30-01-2009 | Denon A/V receiver AVR-1604 powers off | Hi. I have just purchased this unit from ebay.
When you turn it on, it powers up for about 3 seconds and then powers off again.
Any ideas where I can start looking?
Thanks
Dave |
30-01-2009 | Re: start | Audio Output devices and power supply. |
30-01-2009 | | With the set "On"
Cathode of D807 is approx 140.5volt
Cathode of D808 is approx 86.7 volt
Cathode of D809 is approx 8.46 volt
Cathode of D811 is approx.18.3 volt
There is error in my schematic diagram for IC 806 and IC807
Pin 1 as inpu |
30-01-2009 | | With the set "On"
Cathode of D807 is approx 140.5volt
Cathode of D808 is approx 86.7 volt
Cathode of D809 is approx 8.46 volt
Cathode of D811 is approx.18.3 volt
There is error in my schematic diagram for IC 806 and IC807
Pin 1 as inpu |
30-01-2009 | | My current status for IC805 Pin1 reads 13.69volt and pin 3 reads 11.95volt,with J115,J174 jumper wire removed and IC806 pin 3 (floating)
I am able to get 11.95 volt at IC805 pin3 with the three things removed.I have not change IC806 yet.
Sorry for t |
30-01-2009 | Yamaha volume potentiometer | Hello, I have a yamaha htr-5740 receiver and the volume pot is broken. I need to find a replacement, but I cannot seem to find a part number. The only markings on the pot are Alps. I assume that most of their HTR and RV-X line use the same pot.If anyone h |
30-01-2009 | | Pull up dataheets for each. All three are standard (1=In / 2=GND / 3=Out). Schematic does show them (Pin numbers) either incorrectly (or Panasonic are trying to use them unconventionally?)
What about real-world? Do each pin 2 go to same ground "foi |
30-01-2009 | | This Parts & Service manual can now be purchased for $10.77 and downloaded immediately after payment from http://www.justmanuals.com
[email protected] |
30-01-2009 | Re: sources for volume control | http://www.yamaha.com/yec/customer/parts.html?CTID=5010100 or
http://www.yamaha.com/yec/generaldetail.html?CNTID=451690&CTID=5010100 |
30-01-2009 | Hitachi 65F59 Powers OFF | I have an Hitachi 65F59A.
HDMI and Component connections.
From time to time the screen will go totally pink, green or white, then the set turns off. Can power back up with remote immediately after it powers off. This powering off issue may happen once i |
30-01-2009 | | Hi Minnie:
Thanks for the reply. As a newbie, what do you mean 'check e994 to see if it's open'. Visually, everything looks OK. Are you asking for me to check the flow. |
30-01-2009 | | Hi,I've got one in paper form.I am from Poland.
Regards Toma |
30-01-2009 | hitachi 53fdx01b picture goes out when watching dvd. | I'm looking for information on installing the caps described on Hitachi PTV0017 service bulletin. I have the capacitors, but I need to find where they go. Any help, please? |
30-01-2009 | | Sounds more like a flex controller problem. I don't see any bulletins about changing caps on this one. |
30-01-2009 | | Take a multi-meter and put it on ohms, your checking the resistance. It should read a short/close to 0 ohms. |
30-01-2009 | | You have mail. That should fix it. Been there done that on this one. PM if you need help. |