Date | Header | Text |
10-07-2007 | Dell p992 | This is very wierd. This monitor decided it wanted to go fuzzy. It is normally still read-able but it is almost like everyting has a shadow. Now after time (which is not time related) the whole screen goes completely fuzzy. you can't read anything, even i |
10-07-2007 | | OK. The last hour sorting the convergence. I have it set up pretty good. Watchable, but not perfect.
Is there a way I set the convergence permanent so it dont change? And perfect focus? I dont really want to loose it all again, so not sure where to go |
10-07-2007 | mag monitors | hi i'm looking for a mag LT 561d schematic can anyone help |
10-07-2007 | DVX100B repair, I need service manual! | Does anyone know where I can find a DVX100B service manual and schematic?? [email protected], thanks! |
10-07-2007 | Phaser 6300 | How to replace the fuser assembly on the Xerox Phaser 6300?. I could not find the service manual for this printer yet. I need some helps!!. Thanks a lot in advance. :lol: :roll: |
10-07-2007 | | I had similar symptoms and it turned out to be the graphics card in the p.c but first check the monitor settings and update graphics card drivers Worth a try. |
10-07-2007 | A1110 | PLEASE CAN ANY BODY HELP ME ?
I NEED SERVICE MANUAL FOR MY AUDIO AMPLIFIER
SANSUI A1110
THANK YOU |
10-07-2007 | req'd service manual for dscp93a | hi, i'm looking for sevice manual for sony dsc p93a - is there anybody can help me out with this. |
10-07-2007 | | Minnie,
I've studied the schematics extensively but cannot tell which IC controls the Blue Horizontal convergence. Yes, I'm planning on replacing them both but would like to keep the "good" one for a quick temporay fix if/when this happens a |
10-07-2007 | HOT MV7540 p/n P8716AA | TOSHIBA 2SC5447 |
10-07-2007 | | This Parts & Service manual can now be purchased for $9.99 and downloaded immediately after payment from http://www.justmanuals.com/product_info.php?products_id=14329
4mb 47 pages Schematics, Parts-Service
[email protected] |
10-07-2007 | | This Parts & Service manual can now be purchased for $10.79 and downloaded immediately after payment from http://www.justmanuals.com/product_info.php?products_id=12376
41mb 562 indexed and bookmarked pages
[email protected] |
10-07-2007 | | I have the Parts & Service manual up on my site for $9.99 and instant download.
http://www.justmanuals.com/product_info.php?products_id=1881 |
10-07-2007 | | You can either search on the net or post a picture. ... can NOT upload to the forum, but you CAN use any of the photo sites to upload & post the link.
is it any of these?
[img:605bd0fdf4]http://i67.photobucket.com/albums/h287/rramani/test-1.png |
10-07-2007 | Service manual, schematic for Autosound a440 | Hi
I need manual, schematic for [b:dcd7d0f43d]Autosound a440[/b:dcd7d0f43d] or something like that.
Please help.
Regards :wink: |
10-07-2007 | | Can not send or upload manua...
That is ONLY used as a 15 volt clamping diode on a 12V line. Generic number is DZ-15BSAT265. You can use a standard 15 volt zener in it's place.
Provided there are no other problems, unit should power up & opera |
10-07-2007 | kenwood amp no power | model kac-8152d kenwood 1100 watt amp for a car...
does not power up...any help appreciated...thanx |
10-07-2007 | service manual request kenwood kac-8152d car amp | service manual request kenwood kac-8152d car amp
thanx |
10-07-2007 | | Shitty print. |
10-07-2007 | | Add/erase button stores info. The push perfect focus. |
10-07-2007 | | Then push perfect focus. D, whats the exact model #. |
10-07-2007 | | I may pay for the service manual if it can help. I do not want to waste $10 if it is a waste of my time only to find out the part will cost me $100-$150 for the part. ( looked up the price of the flybacks). I saw something in my post I wanted to clarify. |
10-07-2007 | | [quote:05eb7228c8="minnie"]Shitty print.[/quote:05eb7228c8]
If you mean my schematics, you are RIGHT ON! However, the schematics are better than the Japanese-to-English translations.
The BH, BV, RH, RV, GH and GV all leave the convergence board a |
10-07-2007 | | It's a shitty print. All the yolk return resistors should be between 1.2, 1.8, & 2.2 ohms. Just look for obvious discoloration. If you put the original DCU back in the colors should be pretty damn close. When in service mode if you can't adjust a colo |
11-07-2007 | | R7731/7736/7725/7716/7721/7711 1.8 ohm 1 watt. |
11-07-2007 | | the microcntroller usually as an eight pin eeprom associated with it i should check there |
11-07-2007 | Looking for ServManual or schematics for Canon Powershot G3 | G3 ia a digital camera from Canon.
If someone could help with the subj, please, it'd be much appreciated.
Please reply here or in PM if you can help.
Thank you. |
11-07-2007 | | The Model # is the exact same one this thread refers - SP42W5HFX/XEU
(Just double checked on the back! :) ) |
11-07-2007 | | Just had this like this prick today. All the commands I gave are correct. I replaced the IC's and still had no convergence. There's a .47 ohm resistor RF801S. 1 watt. Follow the instructions for senor realignment. Any problems, let me know. |
11-07-2007 | | [quote:194d8fb47c="PGelsman"]I have the Parts & Service manual up on my site for $9.99 and instant download.
http://www.justmanuals.com/product_info.php?products_id=1881[/quote:194d8fb47c]
plamensl
Site Admin
Joined: 14 May 2004
Posts: 135 |
11-07-2007 | | Call for service if you don't know what a resistor is. |
11-07-2007 | | [quote:7d536b0c42="vtech"]Can not send or upload manua...
That is ONLY used as a 15 volt clamping diode on a 12V line. Generic number is DZ-15BSAT265. You can use a standard 15 volt zener in it's place.
Provided there are no other problems, unit s |
11-07-2007 | | I tried the universal one, but it doesnt work :evil:
Was wondering that If I match the wavelength of any other matching remote to that listed in the manual, which I somehow was able to dig out, will it help.
Btw, Manual does not list me the part n |
11-07-2007 | | Take a look here http://www.cmremotes.com/default.aspx?err=E04 |
11-07-2007 | stereo tv | Did you try plugging it in? :roll: |
11-07-2007 | Monitor Problem:Very bright and display screen function is n | Monitor Problem:Very bright and display screen function is not working.I think theres an internal hardware problem,but im not expert in fixing monitor.I need some tip to fix this problem.thanks |
11-07-2007 | same CRT pin system ? | I have come across a few instances where the only problem in 14-inch sets is a weak CRT. I have access to many 14-inch sets with defects in the main board. I would like to swap these weak CRTs with the good CRTs from the bad sets. The pin system in all th |
11-07-2007 | Ps2 Repair | Hi Friends
Im new to the forum and hope that i am posting in the right place.
A friend of mine has done a very stupid thing. We had a power outage here and he decided to connect his ps2 to a generator to play some games. needless to say the generator |
11-07-2007 | | 7411 |
11-07-2007 | | search in zarekmanuals.com |
11-07-2007 | Re: Philips 42" plasma - Chassis LC4.9E AA - need help | [quote:bca3ea81b2="bozzy2006"]Model: 42PF5320/10
Blows 4A fuse at powerup - no picture - audio ok.
I need servicemanual or schematics
thanks in advice.
Jesper[/quote:bca3ea81b2]
for this kind of problem. the only sure way to repair is to re |
11-07-2007 | Re: Any help? | [quote:b2a7d78c0b="SDS"]Sorry but i don't have shematics either.
I have the same model with the same fault, blows 4A fuse on the left plasma supply board.
Short circuit on the +195V, i tracked it down to the hybrid module IC15 under the biggest heatsi |
11-07-2007 | Lanier 6112 | I'm looking for the schematic diagram of lanier 6112. I appreciate any help you can give. |
11-07-2007 | GTV30WLCD | [b]Hi,
Bad news, you need to have the PSU replaced - would cost quite a bit even if you can locate the part.
Try contacting the original supplier or Goodmans to see your luck.
I hope you have tried claiming insurance which is the best approach.[/b] |
11-07-2007 | Need NEC multisyn 5FGP 17" Schematic | I neeed NEC multisuyn 5FGp schematic diagram to find out solution to change
AC supply from 110VAC to 220 VAC . Cuold any one help me.
Thanks so much |