|05-04-2008||magnavox tv||The model # is txk3276 and I lied it is a samsung tv...
Let me know if anyone knows a fix
|05-04-2008||9v to 3v?||Hello
How to supply 3v tv remote control with 9v battery without consumption current (battery) when the remote control is turned off?
|05-04-2008||A normal computer power supply (switch mode power supply, SMPS) will work very well on DC.
But you should not try to power equipment with a conventional mains transformer (say, wall plug adapters etc) on DC. Those will not work and probably the transfo|
|05-04-2008||One possibility is to connect a suitable zener diode in series with the battery. The nearest standard zener voltage is 6,2 V , common types are for example BZX85-C6V2 or BZV79-6V2.
Another possibility is to use a three-leg voltage regulator with extrem|
|05-04-2008||Try temporarily connecting an ordinary 1,5 V dry cell instead of the NiMH cell and see if the unit powers up. (but don't try charging with that cell connected).
A common problem with NiMH (and NiCd) cells is that they can get short circuited after a deep|
|05-04-2008||If you don't own a specialized FBT tester, another possibility is measuring the inductance of the primary winding with a LCR meter. Usually, it is a few mH and, when measured at about 10 kHz, the losses should be very low (high Q factor). Sure signs that |
|05-04-2008||This is common when viewing it in a full-screen session with higher resolution than 1024x768. It is probably due to the used skin for PHPBB.
Try making the web browser window smaller and see if it helps.
Where i am sitting now, i use 1024x768 and have|
|05-04-2008||Looking for Stabilock 4040 radio test sets||Anyone who knows of a Stabilock 4040 that might be for sale, preferrably in northern Europe? It doesn't matter if the instrument is defective or even badly damaged or incomplete, as far as the price is fair.|
|05-04-2008||Did you have tested a switch power suplly with Dc?
I would test monday a Atx power suplly.
If it will work the question is : IT will work 24 of 24 hours?
|05-04-2008||Torbjorn, thank you for your response and you hit the nail right square on the head. I did as you said, only I resized the window manually and it works normal now. I am using a Dell 19" LCD monitor with resolution of 1280x1024, which is the default|
|06-04-2008||RCA Model P52937SG Made March 2002 52"||I have a RCA Model P52937SG Made March 2002 52" TV I bought new and now picture goes like wide screen then bow and then shut off, turn on, shut off, make crackling noise. Can someone tell me what this might be? :cry:|
Thank you. That was very important information. It seems the charger does NOT switch to charging mode. However there seems to be enough power in the cell to run the motor, when the motor is freed from the load of the clipping heads. I'll|
|06-04-2008||Re: Zenith relay 12VDC to 24VDC swap??||[quote:f8dd32a949="jpercell"]I have a Zenith TV (SY3572DT). For a long time I've been trying to locate a power relay for it. Everywhere I look I get "no longer available". The Zenith part number is 195-158; board location is KX3401. It's an Omro|
|06-04-2008||Re: RCA Model P52937SG Made March 2002 52"||[quote:7883d1c22c="drmackenzie"]I have a RCA Model P52937SG Made March 2002 52" TV I bought new and now picture goes like wide screen then bow and then shut off, turn on, shut off, make crackling noise. Can someone tell me what this might be? :cry:[/|
|06-04-2008||technics sl-l20 turntable problem||Hello I hope someone can help me I have a problem with my technics sl-l20 linear tracking turntable. The problem is that the tonearm cues down too fast and the grease on the guid rail is dried up. Thank you I appreciate your help.|
|06-04-2008||Yes, normally it will work very well.|
|06-04-2008||Most Omron relays are industry standard types and compatible relays from other manufacturers (Taiko, SDS, Matsushita, Finder etc) should be easy to find by comparing datasheets. Some relay manufacturers even have cross reference tables that can be useful.|
|06-04-2008||I think that there is not much to do to get the problem solved unless the site's administrator kan get some attention of Vereor, www.vereor.com , who has designed the skin/template (subVereor, can be found under "free phpBB templates on their website|
|06-04-2008||pioneer 200 CD||Hallo ,i have a pioneer 200 CD and now doesnt work and show E 9101 does anyone know what this fault could be ?
Thanks in advance|