Date | Header | Text |
12-02-2006 | | I need service manual of jvc vcr HR-J231MS.
Thanks! |
12-02-2006 | Service Manual for Jvc Subwoffer CS-DA-150 | I'am looking for JVC Cad Subwoofer service manuel CS-DA-150 |
12-02-2006 | | osilisope test points.the numbers are ref. no. to there web.site which you do not have acses to unless you work for them. the best is to stat at the psu work your way along and test every thing ,the problim is more than likely with the vidio decoder chip |
12-02-2006 | | Thank You Gest.
I am working on a Sony KP-51HW40 Projection TV.
When I power up the TV there are a series of clicks from the relays on the power supply and the standby LED flashes 6 times which indicates a Low OCP/OVP, +5 line overloaded or shorted on A |
13-02-2006 | | Problem traced to Nicam board. Needs replacement board. |
13-02-2006 | dell monitor P780 schematic | hi , i need schematic for Dell monitor P780ultraScan can everyone send me this datasheet with electrichal schematic? Thanks. my e-mail is [email protected] |
13-02-2006 | | Correction.
I do get the correct voltages, but the relay shuts down.
This is true with or without the connectors attached to the power supply with the exception of the stanby connector. |
13-02-2006 | JVC RX-3L receiver/amplifier | Gee Jim,
I have a very old, but still going strong JVC RX-3L receiver/amp. of which the remote control is lost. I'd like to construct a new remote control, but need the codes for controlling this device. Any chance you have a servic emanual which shows |
13-02-2006 | miele B865 rotary ironer | Hi is there anyone out there familiar with this rotary ironer that can assist with a roller drive problem ? |
13-02-2006 | Alingment instructions needed phillips/magnavox combo | It is model CCXAT252 manufactured around 1999, not sure who made vcr possibly a Funai unit.
Thanks |
13-02-2006 | help me with a deawoo television | i replace a hiprom an it have a hight problem in a daewoo television how do u program it |
13-02-2006 | Re: help me with a deawoo television | [quote:bdfdd93108="summer"]i replace a hiprom an it have a hight problem in a daewoo television how do u program it[/quote:bdfdd93108] |
13-02-2006 | Ford 20XX radio schematics/repair | Ford radio schematics are near impossible to find as they are only supplied to authorised sevive centres. most ford radios are made by visteon but there maybe different schematics for the same model! for instance the 2006 was made from 1990 to 1996 but th |
13-02-2006 | Mitsubishi TS-4545 schematic/manual needed | Hi,
Having trouble with the Red video circuit. Does anyone have a schematic they can send me for this chassie?
Thanks,
Brian B.
[email protected] |
13-02-2006 | Me too but on a TS-4545 | I'm having the same problem. It's with the Red circuit and after pulling the chassie I've found a burnt choke (on the Red circuit under the Convergance board).
Will let you know if replacing the choke fixes it...
Brian B.
Ps - Here is a link to a |
13-02-2006 | Thanks | Much appreciated |
13-02-2006 | zenith | I agree with Mel,
I was trained on Zeniths in 78'. I not only agree with Mel, I offer our 'Rule of Repair' in my shop. "The only thing worse than a GE on the bench is 2 GE's on the bench" Good luck as you move on! |
13-02-2006 | PCB etching | Radio Shack has the supplies you need, Also Mid-States Electronic Supply.
Did you know..., A black 'Sharpie' permanent marker works just as well as an expensive 'Etch-off' pen! |
13-02-2006 | Canon UCX10 Hi camcorder | Need service manual, especially deck mechanism disassembly and re-assembly. Any help appreciated. |
13-02-2006 | gottem! | fine curved dental forceps- first try. |
13-02-2006 | Dell 1505fp | need service manual for Dell 1505fp lcd monitor made by liteon |
13-02-2006 | | Hello,
I am reviewing all post every day and all spam post are deleted as soon as possible, accounts and ips blocked
I hope it will pass soon |
13-02-2006 | | model??????????????? |
13-02-2006 | hitachi tv vertical hold problem | have a hitachi ct-7899b tv that every 10-15 min the vert hold goes for a min , no vert adjustment on the menus, etc. it doesnt change if I bump it so I assume it isnt a loose solder joint, any ideas? or is it a throw away( I love the tv as it has built |
13-02-2006 | Service Progs for Epson Photo Printers & Multifunctional | Hi!
I need service manuals I service progs for R300, RX500, RX700, R220, SP 1290, SP 890 etc
Who can help, please e-mail...
Beforehands greatful.
With great respect, minos.
e-mail: [email protected] |
13-02-2006 | my NV-ds65 plays and records for 5 secs, then shuts off. | My Nv-ds 65 plays and record for 5 secs and then switches off. The power light then starts to flash and after about 1 minute the camera shuts down completely. I have checked all the menu settings and read the manual from cover to cover with no solution. V |
13-02-2006 | Grundig ST-70 574 SAT--CUC 5820 | I make a post a week ago about a thermic problem, problem who now it is turn out to be a total failure of TV-set.
First symptom occure a year ago: high level of brightness and an intense white image of a program produced geometrical deformation of pictur |
13-02-2006 | Philips L9.2A | I need help. The tv runs for about 8-seconds and goes into standby. When I interrogate the sevice mode, error code 12 (blackcurrent loop unstable) is shown. My problem is to determine the cause. The rgb amps on the tube base pcb are all ok. Could it be th |
13-02-2006 | mitsubishi vs-45501a | I just aquired this tv for free. Worked fine when I first hooked it up for an hour or two. I left the room for a while and came back and had no picyure or sound. Unplugged and tried after about 5 min. and vertical was squished to about half screen height. |
13-02-2006 | phillips car 400 | Please can some one help me. I need code for phillips car 400.
No 90462560
type car 400
Gmo400tl247965 |