Date | Header | Text |
28-06-2008 | Mitsubishi ck-31302 32" TV screen rolling | Hello,
First of all, thanks for this forum and the great help/advice that I have read.
OK, heres the deal.
I have a July 1993 model ck-31302 serial 501772 32" mitsubishi tv, that has a rolling screen problem. I guess you would call it a vert |
28-06-2008 | | Jump out the pip board. |
28-06-2008 | AOC monitor problem | My AOC monitor Model 7Vlr S774AA, works OK for a few minutes but after a while the horizontal output transistor gets so hot and if allowed to run for a longer time the transistor fails. What could be the cause? |
28-06-2008 | Sony CDX-GT220 | Bonjour,
j'ai un autoradio sony CDX-GT220 das mon ancienne voiture. tout allait bien et quand j'ai changé de voiture et que je l ai transféré dans la nouvelle, l'autoradio ne garde plus rien en mémoire quand je retire la clé d |
28-06-2008 | | [quote:662395e2b1="Anonymous"]Jump out the pip board.[/quote:662395e2b1]
Ok, I'm up for that if you think that would solve my problem... But how do I do that? THanks for your time. |
28-06-2008 | car audio | I need a sheme for philps 22DC594/72F. |
28-06-2008 | car audio philips | I need a sheme for philps 22DC594/72F. |
28-06-2008 | | Do you think posting this same message in 2 WRONG forums is going to get you an answer any sooner? |
28-06-2008 | Help service manual AKAI CTP28NTF-E7 | some body can help me...
i can find it. |
28-06-2008 | | [quote:3f9570b184="alltronix"]It is likely the PIP modual is bad. you can bypass it by removeing it and jumpering pins 5 and 11 with a 47m/50v np cap and pins 7 and 9 with a .1m/50v np cap jump pins in the VP connector. you will no longer have PIP but w |
28-06-2008 | try and check this | make sure the vents on both sides of the TV are clean. you should be able to hold a light up to the vents and see inside tv. If not they are dirty and shuting down the tv due to heat. This happened to my tv. Repair man out three times couldnt find the pro |
28-06-2008 | 50ML8105D Magnavox, no picture | Magnavox 50ML8105D projection tv, 1st bulb burn out, got a new one put it in. The screen came on for few seconds. Then went black again. I have sound etc. But ofcourse the bulb does not light so it goes into bulb failure.
Question. could it be the ball |
28-06-2008 | | Is this the POS you have to take the whole back off to replace the lamp? What you can do is remove the back, look for any flip switches and tape them closed and try and start the set. While the lamps trying to fire you should read about +300 volts DC to t |
28-06-2008 | | The pip board is a plug in board to the main chassis. Look for a brown wire going to it. You can jump it by removing the board and jumping pins 5 and 11 with a either a 47uf/50v cap and pins 7 and 9 with a .1uf/50v cap, or just use wire. Most models you d |
28-06-2008 | | I replied to your other post. |
28-06-2008 | Zenith z52z95d Converg. Problems, Need help | Ive done a Google search and found this site.
My Parents Zenith z52z95 has had convergence issues for the past 3 yrs. All 3 colors are off, the white is yellow , the red is blured to the right, and blue is dark and on a slight diagonal ( \ )
I took th |
28-06-2008 | | The 120k resister is for if the video is blurred. What you're describing sounds like a convergence ic issues. z52z95. I'm going strictly on memory. There should be 2 STK392-110's on a board. The bias resisters should be 1 ohm. 6 total resisters. The IC's |
29-06-2008 | Help with grayscale | I have a older hitachi 46 inch I recieved the set at no cost it didnt work I fixed that, He said it was out of convergiance I took out the board and resoldered everything and fixed that. After hours of tinkering with the geometry screws I fixed his attemp |
29-06-2008 | | [quote:24543913f7="minnie"]The pip board is a plug in board to the main chassis. Look for a brown wire going to it. You can jump it by removing the board and jumping pins 5 and 11 with a either a 47uf/50v cap and pins 7 and 9 with a .1uf/50v cap, or just |
29-06-2008 | | [quote:0fc02af508="minnie"]The pip board is a plug in board to the main chassis. Look for a brown wire going to it. You can jump it by removing the board and jumping pins 5 and 11 with a either a 47uf/50v cap and pins 7 and 9 with a .1uf/50v cap, or just |
29-06-2008 | | ONE MORE THING!!!!
what do I do with the pip-c mdule now... it is hanging there by the brown wire. Do I just wrap it in electrical tape and place it some where on the chasis? Or do i cut the brown wire, and remove it completely? Thanks again... |
29-06-2008 | | Wow.
Ok is this something that i should have a repair shop do.
Im pretty good w/ repairs but I need a schematic or manual to go by.
My uncle repairs indust. LCD's for Electrical South. So i could pick his brain too.
The z52z95 may have a D at the en |