| Date | Header | Text |
|---|
| 01-11-2005 | Hitachi CMT-2988 service manual | hi ,
Anybody out here have the service manual for Hitachi CMT-2988?
Thanks
Regards |
| 02-11-2005 | Alpine CDA-9855 owners manual | I just bought an this deck on ebay but it did not come with an owners manual. if anybody could tell me where to find one or whereabouts. please email me at [email protected]
Deeply Appreciated |
| 02-11-2005 | Re: LG STUDIOWORKS MONITOR 454V | [quote:1637c06485="CEZAL"]DOES ANYBODY THE SCHEMATIC FOR PC MONITOR LG 454V?
PLEASE UPLOAD. THANKS[/quote:1637c06485] |
| 02-11-2005 | mitsubishi CS-31303 | I am having the same problem with my TV. Did you ever find an answer and will you share? Thanks |
| 02-11-2005 | | More than likely the problem is with vertical circuit & dried up/leaky capacitors/ cold solder joints etc. Any experienced tech in mitsubishi should be able to repair it, however due to the age & cost involved may not be economical. Tho one of the |
| 02-11-2005 | Service Manual Needed VW Radio | Hello, I need the service manual for the Delta6 Radio (delco) as well as the VW Rhapsody/Seat Symphony (Technisat). I have all the Gamma service manuals as well as the US spec DD preimum if anyone needs them.
Thanks |
| 02-11-2005 | | [size=18:3a143dd913]me too, i really need it too
data sheet, documentation, scheme
all u can please
i got one su-v6x to repair, and all a have made to it fails!!!
plz
thanx
[code:1:3a143dd913][email protected][/code:1:3a143dd913][/si |
| 02-11-2005 | Re: Effect "cushion" Toshiba TP55D80 chassis TAC 9 | [quote:cfd2dcfb02="Johnpe"]Effect "cushion" Toshiba chassis tac9494. Hello colleagues, I have a TV Toshiba TP55D80, the chassis is the TAC 9494. It shows the"cushion" image, that is to say you damage in corrections East/West and out of alignment the co |
| 02-11-2005 | | Ok, here is an update
Spoke to Tiny £1 per min told me to do a factory reset on the plasma,
As if that was going to fix the problem,
Guess what? It didn’t work; I was then told that I would have to pay
£100 each way for them to collect and |
| 02-11-2005 | STR58041 | Need circit diagram |
| 02-11-2005 | H.P CSN EMEA Site: Serial / Productcode match question | Due to the fact that many customers only supply their s/n, when loggin a service call, it sometimes is difficult to find a correct H.P productnumber to verify warranty or find spareparts.
Does anyone have a way to find the corresponding H.P productcode |
| 02-11-2005 | | Uhh, it's already on the main site, just search on "STR58041"
[url]//www.eserviceinfo.com/index.php?what=search[/url]
Grtz Mark |
| 02-11-2005 | | Great tip, Chris.
Grtz Mark |
| 02-11-2005 | | Found this site very usefull also:
[url]http://www.hardwarebook.net/[/url] |
| 02-11-2005 | Re: Sony KV-21GMR1 | [quote="]My sony KV-21GMR1 the raster of my tv is flashing on and off everytime you turn on the power of tv then after 15 minutes the raster of my tv turned to normal condition. what is the problem of this?... can anyone help me? pls... |
| 02-11-2005 | Sanyo M9998 | Hi, have anybody technic data of Sanyo M 9998 ? Or have anybody a user manual? Please send me to my mail: [email protected]. Thanks. |
| 02-11-2005 | Finlux color TV, screen fades in and out | Just purchased a new Finlux TV for my mother-in-law..worked great for 30 seconds and then the screen did a slow fade..but the sound was still crystal clear...then the picture came back for 10 seconds or so and faded out again.
Thought it might be the cab |
| 02-11-2005 | panasonic tx25 | hi i hope some one can help. when watching via rf all ok but when viewing tv,sat or dvd via scart theres no colour HELP |
| 02-11-2005 | logik television manual | does anyone have the service manual for the logik television - model no. lcxw30nn6 - or for any logic tv as i would imagine the basics of these televisions are all the same. |
| 02-11-2005 | | Hello Shai,
It seems like, during transport, a dry solder joint or bad connection has been created.
Due to the fact that the TV is new, just bring it back to your shop and request an other one. It's seems to be a clear warranty case.
Good luck (e |
| 02-11-2005 | | Try changing your PAL/NTSC setting in de "video-setup" menu!!
That should help!
Grtz Mark |
| 02-11-2005 | | thanks for the suggestion. but i cant find that option in the setup |
| 02-11-2005 | SONY CMT EP707, service manual | I need service manuals for this audio or only CD mechanism, |
| 02-11-2005 | Alpine CDA-9855 owners manual | If you go to the Alpine website you can download it.
I found this link under Alpine Europe for CDA-9855R.
http://www.alpine-europe.com/content/cms/index.php?t=204&manualsearch=CDA-9855R |
| 02-11-2005 | | I think dry solder joint or bad connection @ crt socket on crt pcb.
groeten
luc |
| 02-11-2005 | | problem is bad picture tube.
When tv is working you can check it to hit with a screw driver at the neck of the tube.You will see red spots are red flyback lines.
luc |
| 02-11-2005 | | do you have any id what kind of chassis it is.
You can see this at the back side of the set(sticker with serial number) |
| 02-11-2005 | panasonic tx25 | Does it automatically select the AV mode when eg. Sat selected or dvd switched on or do you select AV manually using the t.v remote?
How many scart sockets do you have?
Does the display show AV1 or AV1S? and if the S is displayed this would be the reaso |
| 02-11-2005 | | thanks for the replies folks ill give a full run down. last night was playing ps2 via scart 3 front of tv and it just changed by itself to black and white.dvd player scart 1,sky scart 2 are all the same black and white.but on rf we get colour.scart 2 is t |
| 02-11-2005 | | Solution for this kind of problem, or what I can do to get back the missing red colour? |
| 02-11-2005 | | sorry forgot yes its on av1 etc not s (tried that already) |
| 02-11-2005 | Re: thomson tx92f | [quote:e2b85492ae="bachar"]hello,
when connect the arial or receive a signal the tv (thomson model tx92f )return to sandby what is the cause if you have any idea plz send to me
thanks.
David[/quote:e2b85492ae][color=blue:e2b85492ae][/color:e2b85492ae]s |
| 02-11-2005 | Mitsubishi CT-25AV1BD | I had a similar problem a while ago on a 28" model and fitted the 8V regulator upgrade kit and had to replace IC301 (MSP3410) also.
IC201 (TEA6415C) has been known to cause similar symptoms as well. |
| 02-11-2005 | panasonic tx25 | Interesting.
What happens if you enter the sky menu and change to RGB mode? |
| 02-11-2005 | | I solve this problem before few months...I spend many hours on this problem.Just desolder and take out front switches +p and -p.
good luck. |
| 02-11-2005 | akai tv | ws-p28ntf-sf-d-gb power on led pulsing, tv does not power up just power on led pulses like capacitor charging and discharging :? |
| 02-11-2005 | Re: Philips 9P5511C1 / PTV836 ?? model? chassis? | [quote:bf9ad5d0aa="rmnypt"]I'm having trouble locating information on this projection TV. Philips lists it on their website and you can dowload the user manuals for it, but it is not listed in their model surveys. The chassis number listed on the back o |
| 02-11-2005 | | just changed sky settings still black and white this is looking terminal. |
| 02-11-2005 | panasonic tx25 | mmm Had a look at the circuit diagram for TX-25MD1 (euro 2L chassis) and assuming this is the model then as this fault is present on all av inputs in composite video as well as RGB then I would suspect IC601 video processor (VDP3108-25). |
| 02-11-2005 | Re: do you have yahoo id | Hi Afadar!
My jahoo id is hakkee80. I just made it, so i cant use it yet. But i will try to contact you. i can send the photo in a message? please help me i'm a lame in these things! :) |
| 02-11-2005 | panasonic tx25 | Is the on screen display and teletext o.k? |
| 02-11-2005 | | Whats the power on led doing |
| 02-11-2005 | | ok thanks its a tx25ad1dp. i had a look at the video board and it shares the same ic 601. is this an expensive part and where should i look for one cheers. |
| 02-11-2005 | | Stating that it's a 32" Zenith is too vague for much of any response. What's the model number or chassis number or board numbers. If you're a tech, you've surely checked and or replaced the feedback caps in the primary side of the power supply? |
| 02-11-2005 | | The solution is to purchase another television. As the other poster stated, you probably have a defective picture tube, which would cost more than another set. |
| 02-11-2005 | | First off you said that you're good with a soldering "gun". If you use a soldering "gun" rather than a soldering "pencil" in there, you won't have any board left. Second, replace both IC"s at the same time, never just one. Third, there are upgrade IC's |
| 02-11-2005 | | You neglected to supply a model number! :roll: |
| 02-11-2005 | | Too vague.
Do you have secondary power supply voltages?
Do you have and B+ on the collector of the horizontal output transistor?
When you attempt to power it up, do you get any pulses on any secondary of the IHVT?
If you do, is it correct or is it "to |
| 02-11-2005 | | Since you refuse to go to a "rip off tv shop", just purchase another tv. A 20" television generally isn't worth the money to have repaired. |
| 02-11-2005 | | You're evidently not a tv tech, so any "help" wouldn't help much. |
| 02-11-2005 | Possible to use any power adapter with 220v/50hz? | OK, I have a quick question... :)
Why do some "wall wart" power adapters (transformer from AC to DC) work with 110v/60hz [b:cebf564ea6]and[/b:cebf564ea6] 220v/50hz.. but others do not?
Don't they all have the same electronics inside, with the only |
| 02-11-2005 | panasonic tx25 | I would advise taking the set to a Panasonic dealer to confirm this and obtain an estimate as they are expensive as some are supplied as a kit with an eprom with so many different versions.
If this is the case then some dealers would not charge an estima |
| 02-11-2005 | | Repair should be less than $100.00, no matter the failure. Could be as little as $75.00, which would be well worth it for a 31" television. |
| 02-11-2005 | | It's most definitely a connection problem in the filament circuit for the crt for the fading problem. It could be on the main or crt board.
The auto-program problem, could be an aft alignment problem within the main board. Attempt to manually install |
| 03-11-2005 | | Sorry Guys; I fell asleep and did not check for responses until now. The set s still not working so I still need the schematic. I have sent an e-mail response to Kalp |
| 03-11-2005 | DTK CDD1401 and Markvision VC4968NI Monitors | I need service manuals or schematic diagrams for two old monitors I am trying to repair. They are a DTK model CDD1401 monitor and a Markvision VC4968NI monitor. They are pretty old monitors but I would like to extend the life of both units. I hope someon |
| 03-11-2005 | | A very direct answer to your query is that the specifications printed on the power supply by the manufacturer are just that; if the you deviate fron the parameters indicated the powersupply will malfunction, possibly also damaging itself and anything conn |
| 03-11-2005 | schematic for philips PR1917C125 | Hi, I need a servicemanual or schematic for the Philips PR1917C125 chasis 19A800-7561
my email is [email protected] |
| 03-11-2005 | | Thanks but i don't need schematics, i looking for some user manual to find how to memory new channels. |
| 03-11-2005 | | If you don't know how to repair it then don't respond. Not to be a dick or nethin but I'm trying to find out how to fix a vertical deflection problem. I have wrote to many forums but I can't seem to get any good help. :) |
| 03-11-2005 | | hi, jims
if you have jvc ca-e21lbk and time please send me his service manual via email. my email is: [email protected]
thank you |
| 03-11-2005 | | I most definitely know how to repair a vertical deflection problem, but when you start off with "i refuse to go to a ripoff tv repair shop", you won't get much help from a "ripoff tv repair shop". After 46 years in the service of electronics, we don't ap |
| 03-11-2005 | IBM Monitor 6551-63N | I am experiencing a problem where the monitor appears to be either momentarily turning itself off and back on, a clicking noise is heardn or the degause circuit is kicking in randomly. It looks more like a problem with the power supply, possibly in the |
| 03-11-2005 | IBM Monitor 6551-63N | I am experiencing a problem where the monitor appears to be either momentarily turning itself off and back on, a clicking noise is heard or the degause circuit is kicking in randomly. It looks more like a problem with the power supply, possibly in the s |
| 03-11-2005 | Looking for a Aiwa AV-D58 Service Manual | Good day. I am looking for a service manual for a Aiwa AV-D58. I would appreciate any help. Even if it is just pointing me to a similar product.
Thank you for your time and help.
Michael |
| 03-11-2005 | Service manual for Toyota LiteAce 1993 Van model | anyone who has the above subject manual. Id appreciate it very much! |
| 03-11-2005 | | ok cheers as for going to the panasonic stealers sorry dealers i think ill give that a miss. |
| 03-11-2005 | Re: jvc service manuals for free | [quote:004cd8378e="jims"]i have a wide variaty of jvc service manuals I can send to anyone who needs them[/quote:004cd8378e]
Hi, Jims!
If you have service manual for JVC XV-THA25
please send me via email: sskipin(at)gmail.com
In any case, thanks fo |
| 03-11-2005 | philips 32pw6518/05 LO4E Chassis | Hellocan anybody help picture is shifted to right and is about half
of the screen wide if any body has any service info would appreciate input
Cheers |
| 03-11-2005 | Looking for manual or schematic: cordless tel Sony SPP-57 | I¨m looking for service manual or schematic diagram: Cordless telephone SONY SPP-57 (old FM 49 MHz).
email:
[email protected]
Thanks for any help :D |
| 03-11-2005 | dtr 1500 | Sounds like it is in reset mode...
This is achieved by pressing the + key when connecting the power.
Came across this on another forum when trying to get hold of a copy manual.......
Reset instructions:
disconect power,
keep pressing '+' butt |
| 03-11-2005 | sylvania srt2227 service mode | Need to know how to enter service mode or digital adjustment for this model.
Luis |
| 03-11-2005 | | You must purchase a Funai remote and modify it per Funai's instructions to make a service remote. |
| 03-11-2005 | | As a follow-up to my previous post, that particular Sylvania unit may be a Sears product, of which may not be listed in Funai's manuals. |
| 03-11-2005 | I Have the same problem | Do you fix the problem?. I Have the same situation and I don´t know how to co hange the frecuency parameters. If you already to fix the problem, please tell me how its the procedure |
| 03-11-2005 | I need a service manual for the JVC VHS VCR Model HR-S8000U | I live in Paraguay, Southamerica, and need the service manual and, if possible, the schematic diagram for the JVC VHS VCR model HR-S8000U. Please let me know if you have one. I've got a friend who lives in CA and who can send me the papers from there to P |
| 03-11-2005 | Re: scheme help | [quote:ba27dd3dea="Anonymous"]can someone find me scheme for PHILIPS FW-R7/22[/quote:ba27dd3dea] |
| 03-11-2005 | philips tv 32pw9523/05m chassis smg2.ie | this set is tripping with high pitch noise every 2 or 3 seconds
any tips would be appreciated |
| 03-11-2005 | Re: philips tv 32pw9523/05m chassis smg2.ie | [quote:b59e9ef0d3="willtom"]this set is tripping with high pitch noise every 2 or 3 seconds
any tips would be appreciated[/quote:b59e9ef0d3] i think this should be chassis md2.22e aa |