Date | Header | Text |
28-08-2008 | YIPPEE!!!!!!! | :D
Replaced C707 and E994 and it's working!!!!!!!!
If anyone else has these similar symptoms, examine C707 closely as I could not see the damage until I actually removed it from the board.
This forum Rocks!!!!
Jerry Martire |
28-08-2008 | repair question | I have sound but no picture. Well the picture is snowy red and goes to standby or off in a second. i just replaced the ysus. For the voltages where do you check those at? thank you for any help. |
28-08-2008 | | All the voltages are good. Anything else? Thank you for the help |
28-08-2008 | | White picture, replaced y sustain. Red sparkles and shuts down sounds like a bad panel. :cry: |
28-08-2008 | convergance | i am trying to fix a 53fdx01b. i have the new ic`s but am not sure which resistors to check. can somebody help me so i dont have to check them all? |
28-08-2008 | | um, red snowy picture. You mean its dead |
28-08-2008 | | Hey Minnie I got the front panel off (speaker grills) I know I'm simply missing this button can you tell me where exactly I can find it. Do I need to remove the actual speakers... :roll: ?? |
28-08-2008 | | With the speaker grill off, you see a 'door' that has 4 screws. You remove it to see the bottom's of the crt's. On the left hand side on the board should be the button. |
28-08-2008 | | SUBJECT: DIGITAL CONVERGENCE ADJUSTMENT MODE ACCESS
Details:
In the past, when the technician needed to enter the Digital Convergence Adjustment Mode (DCAM),
it was necessary to open the front of the unit to access the service switch. Now, to access th |
29-08-2008 | BWD 320 Oscilloscope service manual | I am looking for a manual for a BWD 320 Oscilloscope service manual
Thanks George [email protected] |
29-08-2008 | Thomson 28WF64EB widescreen tv | hi all
I have recently been given a Thomson 28WF64E B tv and every 15 mins or so it appears to go into a demo mode displaying set up info etc.
i have no manual for this model and cannot locate one.
also the tv is password protected so i cannot enter to |
29-08-2008 | | LoL ok I finally found it...I'm laughing because I pressed it and this really cool color grid appeared, this is when I realized I hadn't a clue what I was suppose to do next. I tried to use front panel adjustments but really didn't know what i was doing a |
29-08-2008 | | Shit! didn't want to do this but here we go.
Be sure to input the correct signal format for the display that
needs Convergence Touch-Up. NTSC (Normal) or 1080i for (16X9 HD)
You have to do both modes.
Enter DCAM by pressing the
Service Only Sw |
29-08-2008 | Re: convergance | [quote:a560585d46="madman666333"]i am trying to fix a 53fdx01b. i have the new ic`s but am not sure which resistors to check. can somebody help me so i dont have to check them all?[/quote:a560585d46]
Resistor Location Value Part #
RK42 2.2 & |
29-08-2008 | Re: YIPPEE!!!!!!! | [quote:48241e32bb="Anonymous"]:D
Replaced C707 and E994 and it's working!!!!!!!!
If anyone else has these similar symptoms, examine C707 closely as I could not see the damage until I actually removed it from the board.
This forum Rocks!!!!
Je |
29-08-2008 | | Master password is usually 0000. |
29-08-2008 | | Minnie is definitely correct about 0000. Seem to remember something about a "demo" feature in one of the oncsreen menue preferences?
Not sure but I think your set might be similar to [url=http://www.audiovideosupport.eu/media/26652/UK_ICC20.pd |
29-08-2008 | | Default passwords are normally 0000 or 1234. |
29-08-2008 | Car amplifier Fury LB7575 - need scheme. | I need scheme for car amplifier Fury Lb7575 or any similar. I have this amplifier, but some elements in power supply missing (R and C). I wont to try to repaired it. Thank's. |
29-08-2008 | | I disconnected the lower YDRV and i get a snowy top with the bottom half black. Now the set doesnt shut off or go to standby. It stays on. The the voltage check mean the sus boards are good? Thank you for the help. |
29-08-2008 | | :shock: hummm i can follow instructions pretty well but I'm not following you about modes? |