|30-01-2008||Jvc Av-21FMG3B no picture & sound, only timer LED blinki||The Tv is JVC Av-21FMG3B is having no sound & picture , only the timer LED is blinking. The Horizontal Transistor ( HOT) is ok & the voltage on the collector of HOT is 118v but it reduces 1 by 1 to 84v. what could be the problem. help plz|
|30-01-2008||Re: RCA Model F32648||[quote:74ab6281ee="Ringo"]I have an RCA Model # F32648 that is a few years old that stopped working after just a few years. It has been sitting and I would like to try to fix it my self. When I turn it on it jus puts off a high pitch squeal. I can not |
|31-01-2008||Not sure your model is affected||Not sure your model is affected but,
Certain Hitachi projection TVs had a problem with the connections cracking on the yoke PCBs. The process to get at them can be very involved. This occurs where your 4 pin and 7 pin connectors are attached.
|31-01-2008||Electronics Repair Carrer||Hello everyone. I am 18 and considering going to a trade school for electronics repair. What really made me want to consider this is my deep intrest in music. I would be proud to be able to fix radios/stereos haha. I really dont know how carrers in this a|
|31-01-2008||set is fitted with a philips crt, notorious for failing, usually causing variations on the fault you have, to be sure disconnect cathode feed resistors of red and green guns, use wire to link red feed resistor to green cathode, and green feed resistor to|
|31-01-2008||Yes, PTC is faulty. Degaussed the TV with the wand and replaced posistor and all good now!
Thanks for your asistance|
|31-01-2008||[quote:65f1ffa905="gary"]set is fitted with a philips crt, notorious for failing, usually causing variations on the fault you have, to be sure disconnect cathode feed resistors of red and green guns, use wire to link red feed resistor to green cathode, a|
|31-01-2008||Sony CDX-L410 Wiring connection diagram||Hi,
Would anyone have a pinout for the rear 16 pin connector on the Sony AM/FM/CD automotive player? Appreciate your help.
|31-01-2008||dv100 service manual||Does anyone have a service manual for dalvi box dv100?|
|31-01-2008||Brother HL-5240 drum light flashing||Hi
Drum light was flashing on this printer, so I replaced the drum for another(original Brother DR-3100). Followed steps to reset the Drum counter.
However when I close the front, the drum light still flashes.
I try to print a status page , but|
|31-01-2008||Pin probing software||[url=http://www.scanseer.com]Scanseer[/url] -- a software which uses JTAG boundary-scan technology to monitor IC pins and toggle pin states to test PCB interconnections.
|31-01-2008||If you replaced the drum with an OEM drum then you should have no problems. However if you used a refurb'ed drum, then the reset fuse may not have been replaced. Don't take any crap from Brother about it being out of warranty either, insist on help and sp|
|31-01-2008||Paypal or credit cards.
|31-01-2008||You may want to contact Dell. A lot of these batteries are on a product recall.
|31-01-2008||salam||lan benim burda ne işim var kim getirdi la beni buraya döverim ha|
|31-01-2008||sucuk||ulan benim dandik grundig tv bile 15 dakikada imha oluyo ne dedim ben şimdi bende anlamadım siz devam edin ben bidaha gelmem zaten moral bozmayın:D:D:D:D::D:D:D:D:D:D:D::D:D:D:D:D:D:D:D:D:D:D:|
|31-01-2008||BIOS update Mitac 8258D||How update SYS BIOS R1.07 to Mitac 8258D with program FLASHIT?|
|31-01-2008||KBC BIOS I update successfuly with program KBCFLASH:
Start notebook from CD , KBCFLASH/R104.ROM.|
|31-01-2008||Need code for Philips 90dc401||Hello, I'm new here.
I have an electronic workshop. My daily job is repairing TV sets.
Now I have a radio on the workbench wich asks for a code.
the serial number is
I cannot make out the difference between |
|31-01-2008||KBC BIOS R1.04 and SYS BIOS R1.07 to Mitac 8258D:
Program to start notebook from CD is DrDos :
Run: KBCFLASH/R104.ROM update successfuly. :D
Run: FLASHIT/R107.ROM : ID update succesfuly,but SYS BIOS version R1.03(old)
How run FLASHIT and R10|
|31-01-2008||hyundai hlt 3773 LCD stuck in standby||when i plug in the only voltage present is 3.6-4.2v standby ..when i have managed to get it to switch on all the voltages are ok.when it wont switch on i get 3.6-4.2v on standby,if i turn it on i get a quick flash of approx 2.6 v on the 'power on' termina|
|31-01-2008||Re: sucuk||[quote:af82be79d8="namemyok"]ulan benim dandik grundig tv bile 15 dakikada imha oluyo ne dedim ben şimdi bende anlamadım siz devam edin ben bidaha gelmem zaten moral bozmayın:D:D:D:D::D:D:D:D:D:D:D::D:D:D:D:D:D:D:D:D:D:D:[/quote:af82be79d8]|
|31-01-2008||samsung manuals||This website has them but they do charge for them
www mauritron plus com/html/samsung.html|