|28-03-2010||HP 5p printer paper jam||Help. my beloved 5p Printer has never failed me...until now. I had a bad piece of paper jam. i pulld it out (all of it)...straight out, not out and to the right as apparently I should have done. Now it refuses to draw new paper and shuts down with all|
|28-03-2010||I am having the same issue.. Did you find out anything?||I am having the same issue.. Did you find out anything?|
|28-03-2010||What happens if you disconnect the Y sustain board?|
|28-03-2010||Try replacing IC801 STRS5241|
|28-03-2010||As an Electronics Engineer myself i would say wherever you took the radio sounds like they don't have a clue! Any Engineer worth his salt could isolate the section not working and then find the fault without a schematic|
I unplugged the Y sustain board and the same thing occured.
Note: there is a ribbon cable connected to the Y-Main board that I haven't tried to disconnect. Can't really tell how it snaps in, didn't want to break it. If I need to disconnect it I'|
|29-03-2010||Re: reset Onkyo||[quote:f7c70f23b1="hokiedave"]On my Onkyo, turn the unit on, push and hold Video-1, then push Speaker A. It will respond with 'CLEAR'. Mine is still stuck in Protect mode, but maybe this will help someone.[/quote:f7c70f23b1]need to bring to shop.mine ha|
|29-03-2010||Not even a late-comer? Good god this place is a ghost town.
All the capacitors in the area check out on a capacitance meter, and I replaced the two blown resistors with the same values. The 10 ohm one was totally obliterated, just fell apart when tryin|
|29-03-2010||Ugh, that was me... I'd've expected it to ask me to log in if I didn't enter a username above. Guess not.|
|29-03-2010||Anybody? Please?!!......... :(|
|29-03-2010||[quote:dc7b25306d="FalconFour"]Ugh, that was me... I'd've expected it to ask me to log in if I didn't enter a username above. Guess not.[/quote:dc7b25306d]
edit: Mmm, shorted zener diode. Good thing I already ordered a replacement.
edit: EDIT DAMMIT|
|29-03-2010||Let me get this straight. You have a stereo amplifier with one good working channel and one channel that has distortion. And you need a schematic?
Any technician would get this fixed by making comparative readings, ohms and voltage especially, NO schem|
|29-03-2010||What are the effects of a blown Zener diode?||Okay, since nobody's viewing my main topic except a few ghosts :lol: I figure I should reach a broader audience with a more broad question.
I'm trying to track down the cause of a blown MOSFET in the high-voltage side of a switching power supply. I've|
|29-03-2010||my 400D||Hi, it seems i have the same problem with my canon 400D as you in 2007. No power after broken pins on CF card. Could you send me the picture or say where is IC burned exactly? because i cant see your picture in forum http://forum.eserviceinfo.com/viewtopi|
|29-03-2010||UD3/5 CD tray problems||Katz2000
There are a lot of complementary references above but I can't find thye source they are referring to in order to get the instructions that may help me to repair my CD tray issues.|
|29-03-2010||Dodgy CD trays||That's supposed to be Fatz2000 & i'm referring to the pics that were posted somewhere.
Okay, you're right. And I don't mind you teasing me. You're correct: the good channel is a very useful reference. Nevertheless, I value my time. It is significantly more productive to work with a schematic than without.
If anyone has a|
|29-03-2010||jvc ja-s5g||i nid servismanual jvc ja-s5g or shematik listing. pliz.|
|29-03-2010||I have the same problem.|
|29-03-2010||lost remote control unit how can i get a new one||[quote="i have a vrvd64og unit and i lost the remote for it where can i replace at how do i get one|
|29-03-2010||Re: lost remote control unit how can i get a new one||[quote:2704651eb3="[email protected]"][quote="i have a vrvd64og unit and i lost the remote for it where can i replace at how do i get one[/quote:2704651eb3] 5017421025 someone call me please;|