Date | Header | Text |
15-03-2008 | | Sounds like the guide rollers might have come loose from the base?
Try loading a tape & pause it right of way. Can you see the guide rollers all the way up to the "V" stop? |
15-03-2008 | | This Parts & Service manual can now be purchased for $9.99 and downloaded immediately after payment from http://www.justmanuals.com
[email protected] |
15-03-2008 | | I would agree with Neil, a lot of these sets have complicated bus IC's to work the colour, I've repaired a couple of these sets at great cost, only to have them bounce a couple of months into the repair warranty. The result is an irate customer and a cost |
15-03-2008 | Hitachi Projection T.V. | Minnie, I checked the flyback transformer your way then mine. I am going to confirm possible bad windings with my ohm meter tonight. Will let you all know later. |
16-03-2008 | sticky controls | I dug an old Ross Mixer out of the basement and several of the controls were hard to turn, I tried to clean them with NU-TROL and they worked great. Unfortunately after 3-4 days some of them get sticky again. If you turn them several times they loosen up |
16-03-2008 | | Depending on the control type/wear condition, the best product I've used is made by caig labs. Lots of controls (specially the slider type) must have some sort of lubrication which is usually either dried-out or washed out by most "cleaners"
|
16-03-2008 | | [quote:5af343a161="alain28"]sure....
for you
http://pagesperso-orange.fr/alain.mionnet/enii3210j.htm
......
I hope work on N3856VA later.[/quote:5af343a161]
Page
http://pagesperso-orange.fr/alain.mionnet/enii3210j.htm
is updated.
Max from USA h |
16-03-2008 | | The one I mainly use is CPC, the daughter company of Farnell, they have wide range of everything, their catalogue is as thick as a phonebook. |
16-03-2008 | | The answer to that is of course, yes, but the TV world isn't as cheap as the computer world, a new motherboard would most likely set you back well in excess of a £100. Of course the engineer is right, he can't tell you what's wrong with it without ch |
16-03-2008 | Need manual BLAUPUNKT BOSTON RCC45 | Need manual BLAUPUNKT BOSTON RCC45 please |
16-03-2008 | Philips vcr s-vhs vr813 or vr8139 | Hi
I have the following trouble on my s-vhs philips vr813/vr8139
(pal-svhs/secam vhs)
Twice systems give a good picture (color is ok in vhs secam mode but only black and white in s-vhs pal mode.)
The install menu is not displayed on my tv set but |
16-03-2008 | Re: Convergence | [quote:91db29e728="enoughtobdangerous"]Minnie I was wondering if you could tell me why I can't adjust the convergence on my Hitachi 43FDX10B. I replaced the IC chips and resistors to fix that color problem (blue) but the colors are off and bit and the fro |
16-03-2008 | Re: Dead Panasonic TV TC-21SR10M | [quote:ecc0962d11="echobase"]I owned a set of Panasonic TV TC-21SR10M. Recently the set went DEAD with front LED on and I tried to troubleshoot it. I checked almost every parts of the circuit board, from HOT to power supply section but found all major com |
16-03-2008 | Re: Hitachi Projection T.V. | [quote:b0834533b5="joefire"]Hitachi 57twx20b no picture ,sound fine all leds are lit up not blinking I have service manual and started to check i902 at term 4 . Has anyone seen this problem?[/quote:b0834533b5]
I have cures for this one!
billy@fletche |
16-03-2008 | Manual | [b:7568f89374]Hi! I need manual for TV PHILIPS 29PT9007/12.....match line :cry: [/b:7568f89374] |
16-03-2008 | Toshiba Satellite Pro M10-s405 | cj, I have an onboard video problem. When running external monitor just the same. Can you tell me where the video part of the circuit is Ie Icx60000.? Thanks Dude for all the help! |