Date | Header | Text |
12-02-2009 | Dell 1801fp flat panel monitor power supply problem | My dell monitor just died recently, no power.
I am a beginner at electronic repair hope if someone is an expert in this field could give me a few pointers, your help is greatly appreciated.
so here is what i have done so far.
i've opened it up and |
12-02-2009 | PLAYSTATION 2 broken GREAT OPPORTUNITY FOR PARTS! +2 mem crd | [url]http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MESELX:IT&item=180327696466[/url]
just thought i'd suggest |
12-02-2009 | | Do the 5 and 12 volts go up if power supply/inverter board is unplugged from logic/main? |
12-02-2009 | | You did both IC's? And where did you get them? |
12-02-2009 | | Shoot me a email and I'll send you a power supply trouble shooting guide. In this set you can have a bad dig. main not allowing the set to start. |
12-02-2009 | | Plasma. Could be a bad main board, T-con, or panel. I'd start with the T-con. |
12-02-2009 | | I take solder wick and gently rock the smd caps back and forth. I replace them with electrolytic's. Screw the smd's. http://www.ptscorp.com/
Will also repair these mods. |
12-02-2009 | zenith convergence burnt res | local supplier they are sanyo not garbage have used them before from same supply |
12-02-2009 | Toshiba 42h82 | I have a Toshiba 42h82 that turns itself off after being on for a couple of hours. Any idea as to what might be the issue? |
12-02-2009 | | Check the fan operation.
HtH
[email protected] |
12-02-2009 | Pioneer DEH-9800BT LCD Sreen repair | I would like to replace the LCD screen on my Pioneer DEH-9800BT.
any idea if i can purchase a new screen and any info to install it. it worked for my digital camera screen. |
12-02-2009 | | I'd start by replacing the convergence IC's. |
13-02-2009 | | If it keeps blowing the resistors suspect a bad digital convergence unit or a bad ic. You should be able to order the whole convergence board rebuilt.
http://www.tvparts.com/ |
13-02-2009 | | [quote:5a2bafd977="jts1957"]Do the 5 and 12 volts go up if power supply/inverter board is unplugged from logic/main?[/quote:5a2bafd977]
no, i actually tested the power board with out connecting them to the mainboard and the voltage is below 5v and 12v. |
13-02-2009 | | Does it use 2as01 as the regulator driver IC like in Dell 1800? I just got one fixed - Pin #6 to (hot) ground was 6 ohms. |
13-02-2009 | | Thanks minnie,
I emailed you about the power supply troubleshooting guide. I appreciate the help and will post back with the findings. |
13-02-2009 | Any one can repair laser pointer and laser emitter? | We need some one who can help repair laser pointers and other laser stuffs. PM me if you're interested. |
13-02-2009 | service manuel for toshiba tv model 29JZ5 | Hello
Please I need full Service Manual for toshiba tv model 29JZ5ED,DE
thank you very much
Avi polatov
Techie Tv and Vcr |
13-02-2009 | Need scematics for JVC RX-6012 | or maybe a comparable, i.e. RX-6000 ???
The file at the downlod area is missing part 8 of the rar archive.
Many thanks.
Toni100 |
13-02-2009 | Hitachi 27" MTS TV/Monitor. Adjust vertical/Horizontal | I bought this TV around 1987???.
I had it fixed 5 years ago and since then I cannot see the subtitles at the bottom of the screen or sports scores at the top of the screen. I took the back cover off and I looked in the back of the TV and I cannot see any |