| Date | Header | Text |
|---|
| 06-03-2007 | | Replace vertical ic and STILL have lost the top and bottom 2-3 inches of the screen......Like the pic is shrunk down into a letterbox format. The only problem is that I do not have the option to change the aspect ratio anywhere.
I have changed out so |
| 06-03-2007 | SX 950 no audio out | Have you checked your low voltage power supply to verify that all voltages are present? In the process of your cleaning, could you have broken any wires going to the volume control unit? The relays you are referring to, are these the ones you hear click |
| 06-03-2007 | | What is your source? Is it ok in 16X9? |
| 06-03-2007 | | Sounds like the Samsung sets. You get red or blue 'sparckels' Sounds like a bad panel. |
| 06-03-2007 | /sony KV-32S26 | My Sony KV-32S26 is dead. Will not power on at all. Any suggestions or any known common failures to look for?? |
| 06-03-2007 | JVC DVD player stand-by light?? | Tonight, I was messing around with some of the set-up options of my JVC DVD player (XV-NP10S) when I noticed, all of a sudden my DVD screen shut off.. like the player had been turned off. Yet, the green "on" light still showed over the power but |
| 06-03-2007 | Service Manal | Hi
Which One You Need ?
[email protected] |
| 06-03-2007 | | burgundy-I sent you Sony information. |
| 06-03-2007 | IC Overload protector | What is the substitute of IC Overload Protector (N15), 2 pins, and with a rating of 5 amperes? Can I use fusible resistor as a replacement? What will be tha value if ever?...THANKS |
| 06-03-2007 | HOT | Can you give me all possible substitute for this Horizontal Output Transistor 2SD1558? Thanks |
| 06-03-2007 | Service Manual | Can anyone send me a service manual for SONY MODEL 2185MT |
| 06-03-2007 | free schematic diagram of panasonic tv model TH-27XV1 | hello!is there anyone or any website that can give this diagram for FREE!!thanks :D |
| 06-03-2007 | service manual or el diagram for panasonic kxt 61610\30810 | i have need of the service (repair )manual for analogic telephone exchange panasonic kx-t 61610 /30810 or electrical diagram (':(')
Sad
i wait if someone can help-me
thank very much
[size=18:4cf7c0a48d][/size:4cf7c0a48d][color=darkred:4cf7c0a48d][/ |
| 06-03-2007 | | n15 value is 600mA. as it is a safety critical device it should only be replaced with the same device or rating, not a resistor. |
| 06-03-2007 | Behringer X V-amp Schematics, service manual | I desperatly need schematics / service manual for the Behringer X V-AMP
LX-1X since I've lifted some of the print on the PCB while trying to replace the TL072.
Thx!
If you can help, mailto:[email protected] |
| 06-03-2007 | Schematics for Panasonic TC20L3T | Hello. I have a TV Panasonic TC-20L3T and recently it had gone blank. I managed to fix it but still the picture is not OK. Could anybody give me a schematics of this model, I would appreciate it! Thanks in advance. My e-mail is [email protected]. |
| 06-03-2007 | hai | Hello
Please send me code URC24B to TV NEC. Please |
| 06-03-2007 | | My source is just basic cable 4:3. I was watching a nascar race last sunday and everything was normal. Then I lost the top and bottom 2-3 inches. My raster is also missing the top and bottom 2-3 inches. When I put in a letterbox DVD and set the DVD pl |
| 06-03-2007 | | Fixed...............or never broken.
Some genuis from Apex decided to make a remote control for this tv and add dvd controls on the bottom to control a Apex dvd. On this Dvd tv remote there is a little red button that has nothing on it because it is |
| 06-03-2007 | orion | i want the codes for orion for ucr-24b please. i can't find them |
| 06-03-2007 | Samson F800 Audio Amplifier | Hi All
I have a strange problem with my Samson F800 amplifier. The one channel seems to distor frequencies above 2Khz .... injected sinusoid becomes triangular !!!
Can someone please send me a schematic diagram .... I am really desperate !!
Milli |
| 06-03-2007 | Samsung lcd -LE27T51BC | Hello
I am looking for an schema and of an spare part of an Samsung LE27T51BC.......AC230 volt. |
| 06-03-2007 | nokia monitor | Hi i have a Nokia 447ZAPlus 17 inch monitor withe the following problem:
The monitor works fine for a period of time and after a while it goes blank
it does not lose power..the led is still on...it just loses the image going black blank...if i slightl |
| 06-03-2007 | Service Manual | Hi
I Have This Manual
Please E-Mail Me
chiragashah[email protected]
OR
Log On http://www.service-manual-owner.com |
| 06-03-2007 | Hitachi keeps switching off | Hitachi C24W410SN-311 . Fault on this TV . It starts and then immediately switches off. Any suggestions? Picture comes on for maybe 1 second, then TV shuts down, then it tries to switch itself on again. Sometimes if it is disconnected from the mains for 5 |
| 06-03-2007 | JVC AV-28F3SJ Servive Menu's | I have a JVC AV-28F3SJ widescreen television.
I need to know how to access the service / setup menu's (not the user menus) |
| 06-03-2007 | | check r950 in psu, it often goes high in value, should be 68k, resolder regulator ics ic950 and ic951. |
| 06-03-2007 | | set is fitted with vestel 11ak45 chassis. go into main menu and press 4725. lots of info on this site regarding this extremely unreliable "budget" chassis |
| 06-03-2007 | circuit diagram | Does anyone have the circuit diagram for this model? ( Sharp 32LF92H) |
| 06-03-2007 | | SET IS FITTED WITH THE VESTEL 11AK45 CHASSIS, AVAILABLE ON THIS SITE |
| 06-03-2007 | Radio in Opel Astra. Radio type: sc 303 (c) it | Please a need code for this radio.
NO.: 90518554
Type: sc 303 (c) it
W1W
GM230351703892
020093603301700389
My father remember this code, but he died in car accident :(
Please help. |
| 06-03-2007 | Apex GB5108 Projection TV | Ok..I have a problem, or rather, my parents do. They have an Apex projection tv, model GB5108 which is stuck in U Sintl....i dont know if thats a channel or what but its stuck there. And, of course, they don't have the original remote, which isnt being ma |
| 06-03-2007 | pioneer dvd no picture-please help | hello'
i have a pioneer dv-363-k dvd player
when i insert a disc i can only hear the sound but no picture.
i tried to change the rca cables but noting happend.
i opend up the case now but where should i look for a fault???
what could be the problem |
| 06-03-2007 | philips tv picture blur please help a.s.a.p | hello,
I am after some help with my 4year old philips 32pw9618 100hz flat screen tv.I have noticed that the picture became blurred a few days ago and has now got worse.So bad that i can't read the text when bringing up listings on sky.I have spoke to a |
| 06-03-2007 | 27 inch Zenith with dark picture | I have a 27 inch Zenith, tube, that's about 7 or 8 years old, several years it wasn't used. Anyways, ever since this tv was new, the picutre was relatively dark, and the brightness control didn't seem to have much affect, only slight. Now the TV is watc |
| 06-03-2007 | dell E771p | I accidentally removed the connector end of my monitor cable on a dell E771p a 17" monitor.
I got a good cable but not sure which wire connects to which. i wanted to splice the cables and reconnect them.
Could someone please provide me with som |
| 06-03-2007 | RCA 46" Projection TV focusing help | Well, I found this 46" RCA projection tv out by an old dumpster, and it was in REALLY nice shape, so I went ahead and adopted it, thinking I might get lucky and be an easy fix. I took it apart and it turns out the high voltage splitter was arcing to |
| 07-03-2007 | | Dust on the lens, also check your G2/screen setting and your focus settings. There on the same block. |
| 07-03-2007 | | If screen doesn't adjust it to a watchable level, I would say yes the tube is bad unless you have a brightness limiter problem. What's the model? |
| 07-03-2007 | | There's focus control on the flyback, if adjusting that doesn't clear it up, yup, bad tube. Picture looks smeared, funky color, ect. |
| 07-03-2007 | | Glad you got it. So you had you 4X3 picture in the 16X9 mode. Shit happens and when you do lose your vertical deflection which you will, you get it handled! :D |
| 07-03-2007 | | [quote:0637864586="gary"]set is fitted with vestel 11ak45 chassis. go into main menu and press 4725. lots of info on this site regarding this extremely unreliable "budget" chassis[/quote:0637864586]
Gary, we don't say 'budget.'
We say inexp |
| 07-03-2007 | | Check R606, should be a white .10 ohm resistor to see if it's open. |
| 07-03-2007 | | NTE261 |
| 07-03-2007 | Hitachi 43FDX11B Blue shadow/convergence issues. | I have a Hitachi 43fdx11b. While watching tv it devolped a blue shadow. I tired to adjust the blue with the remote but I was unable to move it horizontaly only vertical. I replaced the STK's 2 yrs ago due to a wave at the top of the screen. That |
| 07-03-2007 | Canon PC 950 | Any one have a service manual I can have for this copier. I have to change an exposure lamp and I have never done a photocopier before only printers. Or can any one tell me how to do that? |
| 07-03-2007 | Backing Up my DVD's | I want to make copies of my son's moves. I have dvd Cloner 4 but the quality of the copy is horrible. Is there a better way or program I can use? As far as I can tell the software may be the problem. I know nothing about this so any help will be great
|
| 07-03-2007 | | model number is A27B33W
By the way, turning the adjustment on the flyback did make a bit of a difference, but the picture is still to dark to watch in a lighted room. |
| 07-03-2007 | Sony KV-32S26 | I will check it thursday when I am off work and let you know. I assume this is a common failure in these sets. Are there any other common failures in this model?
Kevin |
| 07-03-2007 | Manual | Hi
Please Send Me Manual
[email protected] |
| 07-03-2007 | D-Link | I have a "D-Link DSL-502T ADSL Router" P/N ISL502TAT.A5...... and Require some information regarding component values.
C118 (surface mount technology capacitor)
and
R144 (surface mount technology resistor)
Thank you for any info |
| 07-03-2007 | LG TV Service Mode Entery | Dear All
Please help to get in the service mode and to adjust picture because it is shifted from what it was when tv was bought. LG Model# 32FS4 series. :( |
| 07-03-2007 | | i usually call them something else, but i was trying to be polite and not insult somebodies pride and joy. |
| 07-03-2007 | | [quote:a4a3356f7c="gary"]set is fitted with vestel 11ak45 chassis. go into main menu and press 4725. lots of info on this site regarding this extremely unreliable "budget" chassis[/quote:a4a3356f7c]
Thanks for your help so far. However it's act |
| 07-03-2007 | | had 2 of those sets recently where the poor focus was caused by the line output transformer itself, the focus controls having hardly any effect, set has a twin focus loptx, ie 2 focus controls at the top and 1 screen control at the bottom, both transforme |
| 07-03-2007 | | http://fileshare.eshop.bg/downloadsm/24558/Vestel_11AK49-6.html
http://fileshare.eshop.bg/downloadsm/23251/vestel_.html |
| 07-03-2007 | | if set has a feature called pure audio make sure it is turned off, had a dv668 last week with same problem and thats all it was, a button on the front |
| 07-03-2007 | | Okay, apologies if I sound dumb.
First one of those files is the circuit diagram. Okay with that.
Second one downloads in three parts 11AK49[1].part1.rar 11AK49[1].part2.rar 11AK49[1].part3.rar
Now excuse my ignorance what is a file with a .rar |
| 07-03-2007 | | you need to download winrar or winace either of which will then extract all 3 sections in one go |
| 07-03-2007 | | Okay, i'm making progress. Have decompressed those files and now have a wealth of service information.
But I am still falling at the first hurdle, how to get into the engineering menu's.
I press the "menu" button on the remote control. T |
| 07-03-2007 | | on some jvc sets service mode is entered by pressing the info key and the muting key simultaneously whilst main menu is on the screen. |
| 07-03-2007 | | if you have already replaced 2 convergence ics, then you need to check resistors right beside ics.usually low value has burnt or gone high.value either 1.5 ohm,1.5 ohm,1.8 ohm or 2.7 ohm. check all then you will be ok. |
| 07-03-2007 | | you need to probably adjust screen and focus controls on focus pack.these are separate from high voltage splitter.it has 6 pots or controls on marked r,g,b,(screen and focus).also maybe in case someone has moved them adjust delta lens focus on top of each |