| Date | Header | Text |
|---|
| 03-06-2008 | | When the fluid is dirty it looks like mountain dew. Instead of clear it's yellowish and brown hunks of crap floating around. |
| 03-06-2008 | | Hello
The fluid actually has very slight tint of yellow.
I have ordered a 16oz of coolant.
The HV block doesn't have scew in leads.
Instead they go directly into the unit.
The number printed on it is 0321F690541
Thanks |
| 03-06-2008 | | There should be 1 screw holding the block in. You should be able to scoot the rubber boot up and it should unplug? |
| 03-06-2008 | | Hi
Here is a picture of the block.
[img:3aa5a38c0d]http://img214.imageshack.us/img214/3918/img6287vq9.jpg[/img:3aa5a38c0d]
[img:3aa5a38c0d]http://img209.imageshack.us/img209/3646/img6298er6.jpg[/img:3aa5a38c0d]
[img:3aa5a38c0d]http://img209.imag |
| 03-06-2008 | | I stand corrected. I forget Phillips equals cheap. Stick with changing the fluid. Also wipe out the inside of the tube also. I use windex and paper towels, |
| 03-06-2008 | | HI
I guess I will change the coolant.
Also there is no way into the lens of the CRT.
There is only one plug to drain/fill the tube. |
| 03-06-2008 | | Replace your convergence IC's. |
| 03-06-2008 | | Hi again
I forgot to mention, there are small droplet of liquid in the CRT. There is no way to get to them.
Thanks |
| 03-06-2008 | | If you look 4 phillips screws hold the lens on. With the lens off you'll see 4 more hex screws. I use a 3.5 mm socket. You can split the tube. It's been awhile. You pull the top of the tube off, it reveals a gasket and the colored lens. Remove the gasket |
| 03-06-2008 | | From link:
Quick guide to removal/install of crt:
Tighten the lens adj nut.
Remove crt board, svm board/windings, yoke/windings, ground wires (suggest labelling/marking posistions so you don't end up with an upside-down picture), and HV anode from Fl |
| 03-06-2008 | | Hi
Sorry for the many questions.
I would like to know if it is possible to remove the entire lens assembly off the CRT gun. The are 4 giant bolts holding the lens assembly, but I wanted to know if I can remove these and have the lens separate for th |
| 04-06-2008 | Toshiba TP61g90/71g90 | This is the model number of your set, and if it is doing the telltale "self-protect" clicking, it is most likely the high voltage protect circuit kicking in. This could be caused by a number of different things within the high voltage circuit, |
| 04-06-2008 | Re: problem with Sanyo DP32746 | I bypassed the fuse temporarily with a GMA fuse of the same rating for test purposes. It blew as soon as I energized the circuit. I also bridged the fuse with a 28v aircraft lamp I had laying around which draws about 2 amps when operated at 12v. I figure |
| 04-06-2008 | | Why would you dig up an old post??? What do you want or what are you selling. Prove me wrong. Unplug the over protect line and if it comes on with out convergence correction it's the convergence IC's. |
| 04-06-2008 | | Coolant between. You have to remove the len's before you can crack the tube. Remove the 4 3.5 mm screws to crack "open" the tube. |
| 04-06-2008 | | Most common failure in the inverters are the fets/mosfets which may damage the driver txformers(s).
Don't waste time trying to repair unless you have experience & access to parts.
Googling your model number pulls several suppliers of boards |
| 04-06-2008 | MAX485E, MAX487E General Description | The MAX481E, MAX483E, MAX485E, MAX487E–
MAX491E, and MAX1487E are low-power transceivers for
RS-485 and RS-422 communications in harsh environments.
Each driver output and receiver input is protected
against ±15kV electro-static discharge (ESD) shocks |
| 04-06-2008 | MB audio 10 cd | Ich hoffe es kann mir jemand hefen
ich brauche den Code für das Radio Alpine audio 10 cd
S.No. AL291011177718
Vielen Dank im voraus |
| 04-06-2008 | Packing laser printer for moving | I need to pack my Brother HL-4040CN laser printer for moving, and upon reading the instructions found that I should have saved the plastic orange pieces that come inside the printer and toner cartridges for this purpose...but I threw them out a year ago w |
| 04-06-2008 | | Usually, it is no problems as far as you treat the printer carefully and don't tip it over. If you want to be very careful, take out the toner cartridge and move it separately, then there is no risk of toner leaking out in the printer. Remember that the s |
| 04-06-2008 | Dumbos who think r/p mosfet will fix!!!. | Lissen you utter !@#$%&^*()!!!S- you must check/r/p comp in circuit- there will be faulty causing mosfet to fail- these guys are reliable AS LONG AS ALL OTHER COMP ARE OK!. B/r from an old bassid. |
| 04-06-2008 | AVR25 | Hello, my AVR25 is shutting down automatically after a few seconds, I'm looking for a service manual to try to fix this (email [email protected]). Much appreciated. |
| 04-06-2008 | AVR25 | Hello, my AVR25 is shutting down automatically after a few seconds, I'm looking for a service manual to try to fix this (email [email protected]). Much appreciated. |
| 04-06-2008 | Easy sharing of digital pictures and images with friends. | It is designed to focus on user experience to do easy sharing of digital pictures and images with friends and other online audience. (blogs etc). when you select browsing, the uploaded files will be queued up for upload and upload will start automatically |
| 04-06-2008 | Temporary fix | Summer just started and my unit is beginning to behave just like that. To temporarily fix the problem (just until my exams are over and I get the time to try and implode the amp by screwing something up) I placed another cooling fan on the top cover. The |
| 04-06-2008 | | This Parts & Service manual can now be purchased for $9.99 and downloaded immediately after payment from http://www.justmanuals.com
[email protected] |
| 04-06-2008 | Datasheet of M56748FD | Please ,I need a datasheet of C.I M56748FP;
Thanks and see you, Kodio |
| 04-06-2008 | | ¿hola, usted consiguió un manual.N-POS=30 de reparaciones para el mkIII del denon dn-2000f? |
| 04-06-2008 | | Common motor driver
http://www.datasheetcatalog.org/datasheet/MitsubishiElectricCorporation/mXturqs.pdf |
| 04-06-2008 | China electronic wholesale?? | Hi all,
Im sorry if this is in the wrong topic or specific post for these types of things
How do you think of china electronics supplier?Have you bought something from china through the internet?How about the quality of all the product?
show your opino |
| 04-06-2008 | recommendation | Could I recommend you some chineses supplier?as we know,the electronic products are very cheap and good in south of China.recently year,there are so many foriegn trade company in China which specialize in the electronic product.so,maybe you can have a try |
| 04-06-2008 | almost fixed it... | Ok, so I did take the board almost all the way out of the TV (the three main red wires were not unplugged), but I did opt to clip the leads and solder the components topside onto the leads, instead of through hole repair...
The c707 was torn, replaced |
| 04-06-2008 | new for you | Hi guy,
why did you want to get a second one.if I say you can get a new one by the same price ,would you??
Hahahaha,,,come on
I would recommend you some online shop which you can buy directly from south of china.they can provide you good quality and re |
| 04-06-2008 | Re: new for you | [quote:6467239325="Jim125"]Hi guy,
why did you want to get a second one.if I say you can get a new one by the same price ,would you??
Hahahaha,,,come on
I would recommend you some online shop which you can buy directly from south of china.they can prov |