Date | Header | Text |
13-07-2010 | Disassembly service manuals | Here is list of dissasembly guides. Video manuals collection.
http://pinout.net/disassemble/
You can search for look inside manuals or just browse categories |
13-07-2010 | kv29 E1E problem | hello every body , I have Sony kv 29 E1E .The problem is gets off after about 5 seconds.when trying to put it on i have to unplug it for about 1 minute.then always the same problem .Any idea about this .trhanks in advance. |
13-07-2010 | Ferguson FL26WX1 | Hello, please can anyone help with Ferguson FL26WX1, 5 1/2 yrs old; just started with intermittent fault, (but getting more frequent) when turning on starts ok but picture goes after few seconds, sound continues ok. Sometimes take numerous attempts before |
13-07-2010 | | Check for puffed lytics in power supply and inverter areas. |
13-07-2010 | Power supply went dead - quote to repair too high | Hello. The power supply in my unit went dead and I got a quote to repair it that is too high for me. Can anyone give me an idea how I could get this done cheaper? What if I buy the part online (I need to find the part number) then where do I find someone |
13-07-2010 | | Power supply from what and what make?
Dave |
13-07-2010 | | Wouldn't be surprised that whatever it is, it's probable that manufacturer's "Top-of-the line" unit. :lol: |
13-07-2010 | | Usually bad soldered joints, we 'call dry joints' that are dull Grey looking with cracks around the soldered lead... but yet again could be capacitor problems.
The usual places are the power supply, line output and driver circuit and also the Frame out |
13-07-2010 | | We need to trace that voltage back to source, usually a regulator... I had something like this in a digital piano but it wasn't a Technics.
I found two chips pulling the 5V rail down... I advised to return it to the makers as these were customized chi |
13-07-2010 | | From time to time we do see burn marks under components that run rather warm... what could have happened is that the heat could have damaged the soldered connection underneath, we call these 'dry joints', they look dull, gray and tired, close inspection m |
13-07-2010 | | try with unstandard search
http://image.pinout.net/pinout_8_pin_files/
find your image and see comments or coment it
Good luck |
13-07-2010 | | try search in pinout.net
http://pinout.net/
or find image like yor connector in
http://image.pinout.net/pinout_sony_files/ |
13-07-2010 | Service manual for Mogen ML-1508TN | Hi all, looking to get into the the service mode for this tv.
Would anyone know how i could get a free copy online of the service manual?
Thx |
13-07-2010 | Re: Power supply went dead - quote to repair too high | hi friend first tel what is the your gadget what is input voltage what is the output voltage then i can help u .to repair |
14-07-2010 | | This is unfortunately a very poorly designed monitor with regards to the control and power buttons. Mine has finally gotten to the point where I can't turn it off if it's on and can't turn it on if it's off the vast majority of the time, sometimes the po |
14-07-2010 | | Ummm, yeah, I'm going to have to retract my remarks and chalk it up to user error on my part.
In the less than 3 years that I've owned this monitor and more than 2 years, I've never noticed that the power button is not actually a push in power button b |
14-07-2010 | service manual nellcor npb 4000 | Dear all, I´m looking for service manual nellcor npb 4000 and I didn´t find in service manuals & datasheets
Thanks for you atention |
14-07-2010 | digital pic frame fault | Hi all
I am trying to repair a digital photo frame i have replaced the ccfl lamps also the inverter
I think the fault is to do with voltages the tubes are trying to light but cant quite ,
on this photo when i unplug the connector circled in yellow i |