|28-01-2011||VCR Sony SLV-T2000VC||Please help with VCR sony slv-t2000vc service manual. Need datasheet for SN761263APG.|
|28-01-2011||is the original horizantol bad??
that sub u use i did not find no spec on it,so if original is still good put it back.If u dont no how to test it u should not try to repair it your self,first you have to check the power supply and flyback area for cold|
|28-01-2011||You can get the Sony SLV-T2000VC service manual at www.schematics.me
|28-01-2011||App for mapping circuits etc||Hey hey,
A friend pointed out a nifty app, called chainr, that can be of great help when it comes to remembering setups, mapping circuits or making a "how to...". It's basically a tool to capture various forms of multimedia and link them to|
|28-01-2011||capacitor is the problem!||Yes, it is the 3300uf @ 100volts cap.
I had the exact problems and sure enough the buldging cap was the problem.
I purchased both the Digikey options you were wondering about just to see which would fit better. I ended up using the 35mmx40mm one (I had|
|28-01-2011||Sanyo DP42746 plasma||No picture I replaced some bad capacitors now all I have is a flashing orange lines in center of screen and sound.This is a sanyo DP42746-plasma.Anybody know whats wrong with it?|
|28-01-2011||An IC on the [b:2a1be0fd23]Power Supply / Inverter[/b:2a1be0fd23] printed circuit board will sense that you only have three of the four CCFL bulbs (two ACROSS the Top & two ACROSS the Bottom) connected - unit will light up for 1-2 seconds and then go |
|28-01-2011||Power supply on flatscreen TV||Yes ,it seems that capacitors are a common fault on LCD screens
Open the back cover and replace the capacitors on the power supply board by GOOD quality and preferably higher capacitance if it fits in the space
Indcontrol Electronics in Australia |
|29-01-2011||I have heard about OPPO but do not have any experience with them or who actually makes it?(back panel layout is very similar to a Matsushita/Panasonic product?). Seemed like it was more geared toward the "videophile" crowd and priced accordingl|
|29-01-2011||I have a TDA8174A as vertical amplifier. My conclusion is that this IC is being put in to shutdown/protection due to some underlying problem. I have replaced it and continue to have the same issues with TV. Any ideas on what to check next?|
|29-01-2011||Thanks again for more input, vtech.
We tend to think similarly when it comes to *phile products. My current speaker wire is #12 low voltage outdoor lighting hookup wire from HD. I did buy some gold plated terminal hardware, but it was the cheapest I co|
|29-01-2011||Does vertical blanking signal make it from the vertical output IC to convergence and microprocessor?|
|29-01-2011||toshiba 42wp48a plasma screen requires warm up?||I'm trying to fix a plasma screen (toshiba 42wp48a) but suspect the problem may be a common one and may have a simple approach for repairs.
I'm not a experienced repair person but have done lots of repairs to simple problems including replacing caps from|
|29-01-2011||On Bulbs||[quote:5f08647b73]An IC on the Power Supply / Inverter printed circuit board will sense that you only have three of the four CCFL bulbs (two ACROSS the Top & two ACROSS the Bottom) connected - unit will light up for 1-2 seconds and then go dark. [/quo|
|29-01-2011||mitsubitshi medias 300 boards, 325m-v controller||Hi does anyone have repair manual for mitsubitshi MC301, MC161-1,MYG250/51,Mc724-1, MC712
|29-01-2011||Re: On Bulbs||[quote:9dde599bbc="Bangonkali"][quote:9dde599bbc]An IC on the Power Supply / Inverter printed circuit board will sense that you only have three of the four CCFL bulbs (two ACROSS the Top & two ACROSS the Bottom) connected - [b:9dde599bbc][i:9dde599bbc|