|01-09-2008||[quote:ea6d52af32="minnie"]Replace the STK392-110's. Could be STK392-150's. Resister values:
Resistor Location Value Part #
RK42 3.3 Ω 1 W AT03202S
RK46 1.8 Ω 1 W AT03195S
RK50 3.3 Ω 1 W AT03202S
RK54 1.8 Ω 1 W A|
|01-09-2008||HELLO I SEARCH FOR SE7889 datasheet||HELLO,
I search for SE7889 datasheet to see that I find a compatible chip to replace it.
In many cases the white screen I have founs that replacing a SMD capacitor placed on the LVDS board.
Please verify that you are getting 3,3 or 5 or 9V on the SMD capacitors placed on the LVDS board, that are paralel conected.
To be more exact|
What do you mean with "with the screen lock applied''
the osd is LOCKED OR ..?|
This fault that you describe it's aboust the INVERTER MODULE.
What I recomend you:
You have on the inverter board that is the same with the power board
some transistors 2SC5707 and some capacitors 150nF/100V
Repalce the capacitors and re|
|01-09-2008||If you are talking about the microcontroller used in samsung monitor, more than likely there is no substitute.|
|01-09-2008||I hate Hitachi's. Convergence can turn in to a real female dog!|
|01-09-2008||Yes you can refill the tube. Coolant leaks usually means the set is junk.|
|01-09-2008||Their called pico fuses. Their usually black from factory.|
|01-09-2008||[quote:960ed3bfcc="pinoyeagle"]Thanks Phils and minnie.
I just found what the problem is. It's a 47uF/35V filter capacitor for AN8032 (active filter control IC) Vcc. :D[/quote:960ed3bfcc]
Sounds about right. :D|
|01-09-2008||Re: mitsubishi vs-45609||[quote:a9d09ea510="joetiz1"]I already have the manuals ..I will try the convergence IC's
hope this works .... I will keep you posted
If you have the service manual don't forget to check the + and - 28vdc pico fuses th|
|01-09-2008||Resolder the flyback first.|
|01-09-2008||I took the crt assembly out. I found a rubber expansion diaphragm on the side broken. Can it be replaced? Can I use any Projection TV Coolant?|
|01-09-2008||Yes and yes.|
|01-09-2008||hysterical Im watching the dog wisperer and just saw your message. The guy was complaining about female dogs...too funny. I'm satisfied with the pic at this point, I'm lucky the TV even works. Earlier today I replaced S901 relay and again everything is fi|
|01-09-2008||MY REMOTE QUIT||MY REMOTE NO LONGER WORKS HITACHI 50DX01B TELEVISION. FRESH BATTERS AND REMOTE LIGHTS UP WHEN BUTTONS PUSHED BUT NO RESPONSE.....|
|01-09-2008||Is the remote set to operate the TV? Sure it's not set to DVD or cable?|
|01-09-2008||REMOTE||YES I'VE PRESSED THE TV BUTTON. I'VE NEVER HAD A PROBLEM WITH IT. ITS WORKING BUT THE TV DOESN'T RESPOND TO ANYTHING AT ALL.|
|01-09-2008||This Parts & Service manual can now be purchased for $9.99 and downloaded immediately after payment from http://www.justmanuals.com
|02-09-2008||Take your cell phone camera and see if the ir is lighting up.|
|02-09-2008||Replace C835 (22MFD/25v)near main regulator IC (IC802)on power /def pcb.|
|02-09-2008||cool just to clarify is 22mfd the part number? and do you know what part this is exactly like a Relay or something?|
|02-09-2008||Do you know where I could get that diaphragm?|
|02-09-2008||[quote:b01897a461="pinoyeagle"]Do you know where I could get that diaphragm?[/quote:b01897a461]
Should be in the service manual.|
|02-09-2008||C835 is a capacitor. C means a capacitor 835 is the location. C835. 22 microfarad 25 volt. Pm Me if you have a problem.|
|02-09-2008||Post it here.|
|02-09-2008||Thanks I kinda figured C was a cap. I will locate the Cap and I think you recommended [email protected] electronics if I recall correctly to order the part.
I really enjoy fixing this stuff and appreciate you help.
Thanks again Minnie. I'm not sure how to PM.. :rol|
Try resoldering the color output IC LM... placed on the CRT board.
If not you most rewritte the Eprom 24C08.|
try resoldering part on inverter board or replace capacitor that are visible damaged on power module.|
Try to uncople the inverter. the inverter is powered using a 3.15 Fuse.
Maybe the Inverter has ocuured a fault.
See if the 12V is stabile. when you connect and siconeect the inverter.|
|02-09-2008||service manual for sony ccd-trv108||hello, i need a service manual for my sony ccd-trv108 hi-8 handycam. Please let me know if you have one. thanks!|
Try resolderind the FBT pins.
And then try to adjust focus.|
folow the 12V from the "+" from the caps that and you wil see that the picofuse is betwen the inverter and the +12 from the capacitors that you have replace it.|
|02-09-2008||If you are lucky only the Fuse is blow.
Close to the power connector inside the nootebook is A SMD FUSE.
Replace'it and see that is workink.
If not then some kind of SMD mosfet transistors are damaged close tot the SMD fuse you have a transistor 2*8|
|02-09-2008||i need this.. thanks!|
|02-09-2008||Service Manual Philips 104s Service Manual||PLease do help me by giving me the service manual for Philips 104s.. Thanks in advance.|
$9.99 and instant download.
|02-09-2008||Obviously someone who didn't read the sticky.
What kind of equipment is it?
But I need a pdf.
The first model was manufactured with Gennesis 5766-LF.
maybe jus some pinouts must be reconfigured.|
|02-09-2008||mitsubishi vs-45609||I have the board out right now and waiting for the ic chip
all the fuses checked good the only question I have is your saying the
convergence IC's but this set seems to only have one stk393-110|