|08-05-2013||Your best bet is to get another power supply and try it. It would have to be 12volts and at least capable of 850 milliamp or more.
AND pay close attention to the polarity of the plug.|
|08-05-2013||Thanx for the offer. I sure hate to see you throw the unit away too.
Certainly you could try the chip. Perhaps I misunderstood, did you say that you tried swapping JUST the mechanism part from the RP unit or the whole mechanism w/pcb? If you did not try|
|08-05-2013||Hi VTech !
Many thanks for the prompt reply.
I opened the beast today, and checked the solder joints. No apparent problem with that.
My husband removed the grey wide cables and put them back (sometimes it works marvel).
At the end it looks li|
|08-05-2013||dvd galaxy ghia||What dvd make is fitted as standard on 2007 galaxy ghia
|08-05-2013||lg 70 inch LCD||I have a problem with a black line down the centre of the tv about 3 inches wide it's driving me mad any ideas what it is thanks|
|08-05-2013||I removed the traverse assembly which has the spindle and tray motors as well as the optical assembly from an RP62 and installed it in the S2300. The terminal pcb (that mounts on the bottom of the traverse) from the s2300 was put on this assembly. The l|
|08-05-2013||Service manual for Ricoh aficio mp 2500||Hi to all, i'm looking for Service manual for Ricoh aficio MP 2500. I must disable ECM on Fax module.
|08-05-2013||Re: aurex toshiba amplifier sb-a70||[quote:470dde1889="ElectroPAN"]ROG sa ma ajute cineva cu shema electronica a amplificatorului AUREX TOSHIBA SB-A70 Va multumesc pentru atentie :([/quote:470dde1889]
i don't speak your language,but i just repaired mine.
I have the manual contact me at |
|09-05-2013||Aha, I see now... It's been a while. All this time I thought the BA Ic was included on the terminal board that sits under the two motors(some Panasonics were). Obviously, that is NOT the configuration you have and indeed it appears to be mounted on the DV|
|09-05-2013||Viewsonic Pwr Supplies-3F01 vs. 3F02||Today I received a new replacement PS for my Viewsonic N3235 and ran into a problem I don't see covered anywhere on the forum.
The old PS is a FSP212-3F01 and it has a CNS1 male 12 pin connector. Looking towards the edge of the PS where CNS1 is, the c|
|09-05-2013||It really irks me when somebody says they've searched but can't find.:roll:
Putting power supply part number in the search box above gives 3 results for the '02' and 12 results for the '01.'
Just doing a rudimentary page by page ctrl 'F' search for the|
|09-05-2013||I got the kit with almost all needed things. It is the same thing for all. No matter whether you are beginner or expert.|
|09-05-2013||Try removing RAM and inserting again in the slot. It may work. It might be the issue of screen flickering or power problem. Does screen turn on in BIOS mode? Submit your queries to [url=http://www.advancedcomputers.co.nz/laptop-repair/]laptop service cent|
|09-05-2013||You can get the Ricoh Aficio MP 2500 service manual at http://service-manuals-schematics.com
|09-05-2013||jts1957, I did spend several hours trying to do various searches to resolve my problem. I read every post on the 'viewsonic 32in lcd tv power supply broken' thread (among others). As you know, that thread is mostly oriented around repair at the compone|
|09-05-2013||Demande D'aide de dèpannage||[quote:8393dd39f2="vtech"]http://forum.eserviceinfo.com/viewtopic.php?p=280794&highlight=#280794[/quote:8393dd39f2]
S'il vous plait. Quelqu'un peut-il m'aider à dépanner cette alimentation...
Je n'ai comme tension que le 3,3 volts.....M|
|09-05-2013||page #6 & page #15|
|10-05-2013||OK, got a chance to work on this again tonight. Just plugging my TV cable into the CNS1 connector of the 3F02 PS was the thing to do.
My confusion on this had to do with information (from several sources) that referred to a "pinout change"|